The array analog input record type is used to read array data. The array data can contain any of the supported data types. The record is in many ways similar to the waveform record. It allows, however, the device support to allocate the array storage.
The record-specific fields are described below, grouped by functionality.
The array analog input record has the standard fields for specifying under what circumstances the record will be processed. These fields are listed in "Scan Fields". In addition, "Scanning Specification" explains how these fields are used. Note that I/O event scanning is only supported for those card types that interrupt.
These fields are configurable by the user to specify how and from where the record reads its data. The INP field determines from where the array analog input gets its input. It can be a hardware address, a channel access or database link, or a constant. Only in records that use soft device support can the INP field be a channel access link, a database link, or a constant. Otherwise, the INP field must be a hardware address. See "Address Specification" for information on the format of hardware addresses and database links.
The DTYP field must contain the name of the appropriate device support module. The values retrieved from the input link are placed in an array referenced by VAL. (If the INP link is a constant, elements can be placed in the array via dbPuts.) NELM specifies the number of elements that the array will hold, while FTVL specifies the data type of the elements.
Field Summary Type DCT Default Read Write CA PP DTYP Device Type DEVICE Yes Yes Yes No INP Input Specification INLINK Yes Yes Yes No NELM Number of Elements ULONG Yes 1 Yes No No FTVL Field Type of Value MENU (menuFtype) Yes Yes No No
Index Identifier Choice String 0 menuFtypeSTRING STRING 1 menuFtypeCHAR CHAR 2 menuFtypeUCHAR UCHAR 3 menuFtypeSHORT SHORT 4 menuFtypeUSHORT USHORT 5 menuFtypeLONG LONG 6 menuFtypeULONG ULONG 7 menuFtypeFLOAT FLOAT 8 menuFtypeDOUBLE DOUBLE 9 menuFtypeENUM ENUM
These parameters are used to present meaningful data to the operator. They display the value and other parameters of the waveform either textually or graphically.
EGU is a string of up to 16 characters describing the units that the array data measures. It is retrieved by the
get_units() record support routine.
The HOPR and LOPR fields set the upper and lower display limits for array elements referenced by the VAL field. Both the
get_control_double() record support routines retrieve these fields.
The PREC field determines the floating point precision with which to display the array values. It is used whenever the
get_precision() record support routine is called.
See "Fields Common to All Record Types" for more on the record name (NAME) and description (DESC) fields.
Field Summary Type DCT Default Read Write CA PP EGU Engineering Units STRING  Yes Yes Yes No HOPR High Operating Range DOUBLE Yes Yes Yes No LOPR Low Operating Range DOUBLE Yes Yes Yes No PREC Display Precision SHORT Yes Yes Yes No NAME Record Name STRING  No Yes No No DESC Descriptor STRING  Yes Yes Yes No
The array analog input record has the alarm parameters common to all record types.
These parameters are used to determine when to send monitors placed on the VAL field. The APST and MPST fields are a menu with choices "Always" and "On Change". The default is "Always", thus monitors will normally be sent every time the record processes. Selecting "On Change" causes a 32-bit hash of the VAL field buffer to be calculated and compared with the previous hash value every time the record processes; the monitor will only be sent if the hash is different, indicating that the buffer has changed. Note that there is a small chance that two different value buffers might result in the same hash value, so for critical systems "Always" may be a better choice, even though it re-sends duplicate data.
Field Summary Type DCT Default Read Write CA PP APST Post Archive Monitors MENU (aaiPOST) Yes Yes Yes No MPST Post Value Monitors MENU (aaiPOST) Yes Yes Yes No HASH Hash of OnChange data. ULONG No Yes Yes No
Index Identifier Choice String 0 aaiPOST_Always Always 1 aaiPOST_OnChange On Change
These parameters are used by the run-time code for processing the array analog input record. They are not configured using a configuration tool. Only the VAL field is modifiable at run-time.
VAL references the array where the array analog input record stores its data. The BPTR field holds the address of the array.
The NORD field holds a counter of the number of elements that have been read into the array.
Field Summary Type DCT Default Read Write CA PP VAL Value DOUBLE No Yes Yes Yes BPTR Buffer Pointer NOACCESS No No No No NORD Number elements read ULONG No Yes No No
The following fields are used to operate the array analog input record in the simulation mode. See "Simulation Mode" for more information on the simulation mode fields.
Field Summary Type DCT Default Read Write CA PP SIOL Sim Input Specifctn INLINK Yes Yes Yes No SIML Sim Mode Location INLINK Yes Yes Yes No SIMM Simulation Mode MENU (menuYesNo) No Yes Yes No SIMS Sim mode Alarm Svrty MENU (menuAlarmSevr) Yes Yes Yes No
static long init_record(aaiRecord *prec, int pass)
If device support includes
init_record(), it is called.
Checks if device support allocated array space. If not, space for the array is allocated using NELM and FTVL. The array address is stored in the record.
This routine initializes SIMM with the value of SIML if SIML type is CONSTANT link or creates a channel access link if SIML type is PV_LINK. VAL is likewise initialized if SIOL is CONSTANT or PV_LINK.
This routine next checks to see that device support is available and a device support read routine is defined. If either does not exist, an error message is issued and processing is terminated
static long process(aaiRecord *prec)
See "Record Processing" section below.
static long cvt_dbaddr(DBADDR *paddr)
This is called by dbNameToAddr. It makes the dbAddr structure refer to the actual buffer holding the result.
static long get_array_info(DBADDR *paddr, long *no_elements, long *offset)
Obtains values from the array referenced by VAL.
static long put_array_info(DBADDR *paddr, long nNew)
Writes values into the array referenced by VAL.
static long get_units(DBADDR *paddr, char *units)
static long get_precision(DBADDR *paddr, long *precision)
Retrieves PREC if field is VAL field. Otherwise, calls
static long get_graphic_double(DBADDR *paddr, struct dbr_grDouble *pgd)
Sets the upper display and lower display limits for a field. If the field is VAL the limits are set to HOPR and LOPR, else if the field has upper and lower limits defined they will be used, else the upper and lower maximum values for the field type will be used.
Sets the following values:
upper_disp_limit = HOPR lower_disp_limit = LOPR
static long get_control_double(DBADDR *paddr, struct dbr_ctrlDouble *pcd)
Sets the upper control and the lower control limits for a field. If the field is VAL the limits are set to HOPR and LOPR, else if the field has upper and lower limits defined they will be used, else the upper and lower maximum values for the field type will be used.
Sets the following values
upper_ctrl_limit = HOPR lower_ctrl_limit = LOPR
Routine process implements the following algorithm:
Check to see that the appropriate device support module exists. If it doesn't, an error message is issued and processing is terminated with the PACT field still set to TRUE. This ensures that processes will no longer be called for this record. Thus error storms will not occur.
Call device support read routine
If PACT has been changed to TRUE, the device support read routine has started but has not completed writing the new value. In this case, the processing routine merely returns, leaving PACT TRUE.
Check to see if monitors should be invoked.
Alarm monitors are invoked if the alarm status or severity has changed.
Archive and value change monitors are invoked if APST or MPST are Always or if the result of the hash calculation is different.
NSEV and NSTA are reset to 0.
Scan forward link if necessary, set PACT FALSE, and return.
Each array analog input record record must have an associated set of device support routines. The primary responsibility of the device support routines is to obtain a new array value whenever
read_aai() is called. The device support routines are primarily interested in the following fields:
Device support consists of the following routines:
long report(int level)
This optional routine is called by the IOC command
dbior and is passed the report level that was requested by the user. It should print a report on the state of the device support to stdout. The
level parameter may be used to output increasingly more detailed information at higher levels, or to select different types of information with different levels. Level zero should print no more than a small summary.
long init(int after)
This optional routine is called twice at IOC initialization time. The first call happens before any of the
init_record() calls are made, with the integer parameter
after set to 0. The second call happens after all of the
init_record() calls have been made, with
after set to 1.
long init_record(dbCommon *precord)
This routine is optional. If provided, it is called by the record support
long get_ioint_info(int cmd, dbCommon *precord, IOSCANPVT *ppvt)
This routine is called by the ioEventScan system each time the record is added or deleted from an I/O event scan list. cmd has the value (0,1) if the record is being (added to, deleted from) an I/O event list. It must be provided for any device type that can use the ioEvent scanner.
long read_aai(dbCommon *precord)
This routine must provide a new input value. It returns the following values:
Soft Channel device support module is provided to read values from other records and store them in arrays. If INP is a constant link, then read_aai does nothing. In this case, the record can be used to hold arrays written via dbPuts. If INP is a database or channel access link, the new array value is read from the link. NORD is set.
This module places a value directly in VAL and NORD is set to the number of items in the array.
If the INP link type is constant, then NORD is set to zero.
Hey! The above document had some coding errors, which are explained below:
Unknown directive: =fields