Histogram Record (histogram)

The histogram record is used to store frequency counts of a signal into an array of arbitrary length. The user can configure the range of the signal value that the array will store. Anything outside this range will be ignored.

Parameter Fields

The record-specific fields are described below.

Read Parameters

The SVL is the input link where the record reads its value. It can be a constant, a database link, or a channel access link. If SVL is a database or channel access link, then SGNL is read from SVL. If SVL is a constant, then SGNL is initialized with the constant value but can be changed via dbPuts. The Soft Channel device support module can be specified in the DTYP field.

The ULIM and LLIM fields determine the usable range of signal values. Any value of SGNL below LLIM or above ULIM is outside the range and will not be stored in the array. In the NELM field the user must specify the array size, e.g., the number of array elements. Each element in the NELM field holds the counts for an interval of the range of signal counts, the range specified by ULIM and LLIM. These intervals are determined by dividing the range by NELM:

FieldSummaryTypeDCT DefaultReadWriteCA PP
SVLSignal Value LocationINLINKYes YesYesNo
SGNLSignal ValueDOUBLENo YesYesNo
DTYPDevice TypeDEVICEYes YesYesNo
NELMNum of Array ElementsUSHORTYes1YesNoNo
ULIMUpper Signal LimitDOUBLEYes YesYesNo
LLIMLower Signal Limit DOUBLEYes YesYesNo

Operator Display Parameters

These parameters are used to present meaningful data to the operator. These fields are used to display the value and other parameters of the histogram either textually or graphically. See Fields Common to All Record Types for more on the record name (NAME) and description (DESC) fields.

FieldSummaryTypeDCT DefaultReadWriteCA PP
NAMERecord NameSTRING [61]No YesNoNo
DESCDescriptorSTRING [41]Yes YesYesNo

Alarm Parameters

The Histogram record has the alarm parameters common to all record types. Alarm Fields lists the fields related to alarms that are common to all record types.

Monitor Parameters

The MDEL field implements the monitor count deadband. Only when MCNT is greater than the value given to MDEL are monitors triggered, MCNT being the number of counts since the last time the record was processed. If MDEL is -1, everytime the record is processed, a monitor is triggered regardless.

If SDEL is greater than 0, it causes a callback routine to be called. The number specified in SDEL is the callback routines interval. The callback routine is called every SDEL seconds. The callback routine posts an event if MCNT is greater than 0.

FieldSummaryTypeDCT DefaultReadWriteCA PP
MDELMonitor Count DeadbandSHORTYes YesYesNo
SDELMonitor Seconds DbandDOUBLEYes YesYesNo

Run-time and Simulation Mode Parameters

These parameters are used by the run-time code for processing the histogram. They are not configurable by the user prior to run-time. They represent the current state of the record. Many of them are used to process the histogram more efficiently.

The BPTR field contains a pointer to the unsigned long array of frequency values. The VAL field references this array as well. However, the BPTR field is not accessible at run-time.

The MCNT field keeps counts the number of signal counts since the last monitor was invoked.

The collections controls field (CMD) is a menu field with five choices:

IndexIdentifierChoice String
0 histogramCMD_Read Read
1 histogramCMD_Clear Clear
2 histogramCMD_Start Start
3 histogramCMD_Stop Stop

When CMD is Read, the record retrieves its values and adds them to the signal array. This command will first clear the signal counts which have already been read when it is first invoked.

The Clear command erases the signal counts, setting the elements in the array back to zero. Afterwards, the CMD field is set back to Read.

The Start command simply causes the record to read signal values into the array. Unlike Read, it doesn't clear the array first.

The Stop command disables the reading of signal values into the array.

The Setup command waits until the start or read command has been issued to start counting.

The CSTA or collections status field implements the CMD field choices by enabling or disabling the reading of values into the histogram array. While FALSE, no signals are added to the array. While TRUE, signals are read and added to the array. The field is initialized to TRUE. The Stop command is the only command that sets CSTA to FALSE. On the other hand, the Start command is the only command that sets it to TRUE. Thus, Start must be invoked after each Stop command in order to enable counting; invoking Read will not enable signal counting after Stop has been invoked.

A typical use of these fields would be to initialize the CMD field to Read (it is initialized to this command by default), to use the Stop command to disable counting when necessary, after which the Start command can be invoked to re-start the signal count.

The WDTH field is a private field that holds the signal width of the array elements. For instance, if the LLIM was configured to be 4.0 and ULIM was configured to be 12.0 and the NELM was set to 4, then the WDTH for each array would be 2. Thus, it is (ULIM - LLIM) / NELM.

FieldSummaryTypeDCT DefaultReadWriteCA PP
VALValueULONG[]No YesYesNo
MCNTCounts Since MonitorSHORTNo YesNoNo
CMDCollection ControlMENU (histogramCMD)No YesYesNo
CSTACollection StatusSHORTNo1YesNoNo
WDTHElement WidthDOUBLENo YesNoNo

The following fields are used to operate the histogram record in simulation mode. See "Fields Common to Many Record Types" for more information on the simulation mode fields.

FieldSummaryTypeDCT DefaultReadWriteCA PP
SIOLSimulation Input LinkINLINKYes YesYesNo
SVALSimulation ValueDOUBLENo YesYesNo
SIMLSimulation Mode LinkINLINKYes YesYesNo
SIMMSimulation ModeMENU (menuYesNo)No YesYesNo
SIMSSimulation Mode SeverityMENU (menuAlarmSevr)Yes YesYesNo

Record Support

Record Support Routines


Using NELM, space for the unsigned long array is allocated and the width WDTH of the array is calculated.

This routine initializes SIMM with the value of SIML if SIML type is CONSTANT link or creates a channel access link if SIML type is PV_LINK. SVAL is likewise initialized if SIOL is CONSTANT or PV_LINK.

This routine next checks to see that device support and a device support read routine are available. If device support includes init_record(), it is called.


See next section.


Special is invoked whenever the fields CMD, SGNL, ULIM, or LLIM are changed.

If SGNL is changed, add_count is called.

If ULIM or LLIM are changed, WDTH is recalculated and clear_histogram is called.

If CMD is less or equal to 1, clear_histogram is called and CMD is reset to 0. If CMD is 2, CSTA is set to TRUE and CMD is reset to 0. If CMD is 3, CSTA is set to FALSE and CMD is reset to 0.

clear_histogram zeros out the histogram array. add_count increments the frequency in the histogram array.


This is called by dbNameToAddr. It makes the dbAddr structure refer to the actual buffer holding the array.


Obtains values from the array referenced by VAL.


Writes values into the array referenced by VAL.

Record Processing

Routine process implements the following algorithm:

  1. Check to see that the appropriate device support module exists. If it doesn't, an error message is issued and processing is terminated with the PACT field set to TRUE. This ensures that processes will no longer be called for this record. Thus error storms will not occur.
  2. readValue is called. See "Input Records" for more information
  3. If PACT has been changed to TRUE, the device support read routine has started but has not completed writing the new value. In this case, the processing routine merely returns, leaving PACT TRUE.
  4. Add count to histogram array.
  5. Check to see if monitors should be invoked. Alarm monitors are invoked if the alarm status or severity has changed. Archive and value change monitors are invoked if MDEL conditions are met. NSEV and NSTA are reset to 0.
  6. Scan forward link if necessary, set PACT and INIT to FALSE, and return.

Device Support

Fields Of Interest To Device Support

The device support routines are primarily interested in the following fields:

FieldSummaryTypeDCT DefaultReadWriteCA PP
PACTRecord activeUCHARNo YesNoNo
NSEVNew Alarm SeverityMENU (menuAlarmSevr)No YesNoNo
NSTANew Alarm StatusMENU (menuAlarmStat)No YesNoNo
SVLSignal Value LocationINLINKYes YesYesNo
SGNLSignal ValueDOUBLENo YesYesNo

Device Support Routines

Device support consists of the following routines:

long report(int level)

This optional routine is called by the IOC command dbior and is passed the report level that was requested by the user. It should print a report on the state of the device support to stdout. The level parameter may be used to output increasingly more detailed information at higher levels, or to select different types of information with different levels. Level zero should print no more than a small summary.

long init(int after)

This optional routine is called twice at IOC initialization time. The first call happens before any of the init_record() calls are made, with the integer parameter after set to 0. The second call happens after all of the init_record() calls have been made, with after set to 1.



This routine is called by the record support init_record() routine. It makes sure that SGNL is a CONSTANT, PV_LINK, DB_LINK, or CA_LINK. It also retrieves a value for SVL from SGNL. If SGNL is none of the above, an error is generated.



This routine is called by the record support routines. It retrieves a value for SVL from SGNL.

Device Support For Soft Records

Only the device support module Soft Channel is currently provided, though other device support modules may be provided at the user's site.

Soft Channel

The Soft Channel device support routine retrieves a value from SGNL. SGNL must be CONSTANT, PV_LINK, DB_LINK, or CA_LINK.