VacApp Modules:

For external  use:
vacSupport.dbd
libvac.a(so)

Internals:
vsRecord.c
vsRecord.dbd
devVacSen.h             
devVacSen.c               
devVacSen.dbd             

choiceDigitel.h           
digitelRecord.dbd         
digitelRecord.c           
devDigitelPump.h          
devDigitelPump.c          
devDigitelPump.dbd        


vacAppCommonInclude.dbd  
vacAppInclude.dbd
vacAppVXInclude.dbd


August 2007.   Mohan Ramanathan

At this time the module has support for vacuum sensors GP307, GP350, Televac MM200
October 2014:
The new Televac controller CC10 has been aded to the Vac Sensor.

For the Ion pumps we have support for PI Digitel 500/1500 and the MPC (Gamma One)

Support for newer devices will be added at a later date.

The generic record "vs" is for the vac sensors. this record and 
the associated devVanSen supports the following gauges:
	GP307,  GP350,  MM200 (Televac) and CC10 (Televac)
	
The startup file  has the following substitution:
The database has a field called "TYPE" which has to be set correctly. 
vs.db has various substitions for startup file.  
  If address is 0 then it is RS232 
  For RS485 Address has to be a positive number
	for GP350 has to be between 1 and 31 of the form "AA"
 	for MM200 has to be between 0 and 59 of the form [0..9..A..Z..a..z]
	for CC10 has to be between 0 and F  in HEX
      Also for GP350 the prefix is "#" so we will force for MM200 the same!!
 	  for CC10  the prefix is <STX>  = hex 02

excerpts for an example st.cmd file:

#  For GP307 the STN are irrelavent
#   GP307 expects "\n\r" for EOS for both inputs and outputs.
dbLoadRecords("db/vs.db", "P=MR:,GAUGE=VS1,PORT=serial1,ADDR=0,DEV=GP307,STN=0")
tyGSAsynInit("serial1",  "UART0", 0, 9600,'E',1,7,'N',"\r\n","\r\n")  

#  For GP350 STN is irrelavant
#   GP350 expects "\r" for EOS for both inputs and outputs.
dbLoadRecords("db/vs.db", "P=MR:,GAUGE=VS2,PORT=serial2,ADDR=0,DEV=GP350,STN=0")
tyGSAsynInit("serial2",  "UART0", 1, 9600,'N',1,8,'N',"\r","\r")  

#  For MM200 the Televac has two cold cathodes and a minimum of 2 convectrons
#	if STN is either 5/6 then the corresponding CV1 are 1/2 and CV2 are 3/4
#	if STN is either 3/4 then the corresponding CV is 1/2 and no CV2
#   MM200 expects "\r" for EOS for both inputs and outputs.
dbLoadRecords("db/vs.db", "P=MR:,GAUGE=VS3,PORT=serial3,ADDR=0,DEV=MM200,STN=3")
dbLoadRecords("db/vs.db", "P=MR:,GAUGE=VS4,PORT=serial3,ADDR=0,DEV=MM200,STN=4")
tyGSAsynInit("serial3",  "UART0", 2, 9600,'N',1,8,'N',"\r","\r")  

#  Alternative for MM200: specify CV1, CV2, and SPT directly.  If you specify more than
#  one number for STN, the code expects you to specify all four.
dbLoadRecords("db/vs.db","P=MR:,GAUGE=VS3,PORT=serial3,ADDR=0,DEV=MM200,STN=3 1 0 1")
dbLoadRecords("db/vs.db","P=MR:,GAUGE=VS4,PORT=serial3,ADDR=0,DEV=MM200,STN=5 1 0 2")
tyGSAsynInit("serial3",  "UART0", 2, 9600,'N',1,8,'N',"\r","\r")  

#  For CC10 the Televac has a diode and the cold cathode integrated into one unit.
#  It has three setpoints which are being read
dbLoadRecords("db/vs.db", "P=MR:,GAUGE=VS1,PORT=serial3,ADDR=1,DEV=CC10,STN=0")
tyGSAsynInit("serial3",  "UART0", 2, 9600,'N',1,8,'N',"\r","\r")  



#  For Digitel 500/1500 the DEV= D500 or D1500.  The device talks only at 9600 7 E 1
#  Also the  input EOS to device is "\r" while out from device is "\n\r"
#  THE ADDR is irrelvant and STN stands for the no of setpoints from 0-3
dbLoadRecords("db/digitelPump.db", "P=MR:,PUMP=IP1,PORT=serial5,ADDR=0,DEV=D500,STN=2")
tyGSAsynInit("serial5",  "UART0", 4, 9600,'E',1,7,'N',"\n\r","\r")  

#  For Gamma One MPC MPCe also LPC and SPC .  Device supports both RS232 and RS485
#  THE ADDR is addreess of device (both RS232 and RS485
#  STN stands for the no of the pump (MPC can do 2 devices) so 1 for pump1 and 2 for pump 2
#  Then the corrresponding setpoints are odd and even for the respective pumps.
dbLoadRecords("db/digitelPump.db", "P=MR:,PUMP=IP2,PORT=serial6,ADDR=5,DEV=MPC,STN=1")
dbLoadRecords("db/digitelPump.db", "P=MR:,PUMP=IP3,PORT=serial6,ADDR=5,DEV=MPC,STN=2")
tyGSAsynInit("serial6",  "UART0", 5, 9600,'N',1,8,'N',"\r","\r")