Experimental Physics and Industrial Control System
Hello Nick,
We have requested equipment group to consider Ethernet
connectivity since 15 years ago, because of lack of our
manpower. 10 years ago the number of PLCs exceeded 120, and
now 180 for 600m KEK Linac. Some of them strictly required
robustness of PLCs, but many other mainly require remote I/O
capabilities. Most of them were from Yokogawa, mainly because
only Yokogawa had provided program download capability over
Ethernet. They were relatively reliable. That was a period
of "Everywhere TCP".
CAMAC crates, GPIB instruments, temperature sensors, etc.
were connected over TCP, and some others were connected thru
Lantronix XPort. "Everywhere TCP" was remote I/O over
Ethernet.
Nowadays at KEKB, we move further to "Everywhere EPICS-IOC".
We started to embed IOCs on to controllers. If we have to
think about failure recovery, etc for remote I/O, why we don't
just use Channel Access. If we use IOC, we can use database
links, sequencer, as well as CA.
As we asked Yokogawa to provide Linux CPU on PLC, we started
to embed IOCs on to Yokogawa PLCs. That eliminates the code
managements at two places of PLC and IOC. We don't need
ladder program conversion to XML. It is a kind of "Poorman's
VME", instead of PLC.
While we keep many VMEs, we are using/evaluating
IOC on PLCs
IOC on Windows on oscilloscopes
IOC on FPGAs
IOC on microTCA/AMC (on FPGA)
I admit that some of them are not cheap, but the balance
between resources justify them.
We are now studying the balance to configuration management
of the infrastructure like name servers, gateways, etc.
Cheers, Kazuro.
>>> On Wed, 16 Dec 2009 12:44:54 JST, <[email protected]> wrote;
>
> At Diamond we are considering what to use for the next generation of
> discrete I/O. Currently we have a lot of VME based hardware, but we are
> considering a good architecture for a Linux world.
>
> The model that we are considering is a soft IOC on a Linux system
> communicating over Ethernet using an open, industry standard protocol to
> distributed DIN-Rail mounted I/O points. These I/O points take in
> Ethernet and are powered from a 24V bus that will run around the
> hardware area.
>
> This eliminates any dependence on a specialized bus architecture (apart
> from Ethernet) on the Linux system, so they can be commodity PC's, and
> hopefully allows us to use widely available, cheap, industrial modules
> for I/O. It will not completely replace all of the requirements
> currently serviced by VME, but would be able to satisfy most of them,
> with the remaining few being serviced by the occasional VME system (or
> FPGA, or some other bus, or something else entirely in the future...).
>
> This email is to poll the EPICS community as to the experience people
> have had, and recommendations for and against.
>
> The sort of thing we have identified are:
>
> 1. Modbus/TCP based modules, such as the Acromag Busworks series
> http://www.acromag.com/models.cfm?Product_Function_ID=28&Category_ID=22&
> Group_ID=2
> 2. EtherCAT base modules, such as those from Beckhoff:
> http://www.beckhoff.com/
> 3. Standard PLC systems where (as distinct from the other two), you
> take Ethernet to a PLC controller which then has a series of modules it
> talks to in a variety of possible ways.
>
> So, is anyone willing to share their experiences with these or similar
> systems,
>
> Cheers,
>
> Nick Rees
> Principal Software Engineer Phone: +44 (0)1235-778430
> Diamond Light Source Fax: +44 (0)1235-446713
>
> --
> This e-mail and any attachments may contain confidential, copyright and or privileged material, and are for the use of the intended addressee only. If you are not the intended addressee or an authorised recipient of the addressee please notify us of re
> ceipt by returning the e-mail and do not use, copy, retain, distribute or disclose the information in or attached to the e-mail.
> Any opinions expressed within this e-mail are those of the individual and not necessarily of Diamond Light Source Ltd.
> Diamond Light Source Ltd. cannot guarantee that this e-mail or any attachments are free from viruses and we cannot accept liability for any damage which you may sustain as a result of software viruses which may be transmitted in or with the message.
> Diamond Light Source Limited (company no. 4375679). Registered in England and Wales with its registered office at Diamond House, Harwell Science and Innovation Campus, Didcot, Oxfordshire, OX11 0DE, United Kingdom
-----
Kazuro FURUKAWA <[email protected]>
Linac&KEKB, High Energy Accelerator Research Organization (KEK), Japan
Telephone: +81-29-864-5200 x4316, Facsimile: +81-29-864-0321
- References:
- Remote I/O nick.rees
- Navigate by Date:
- Prev:
Re: Remote I/O Stephen Lewis
- Next:
RE: Remote I/O nick.rees
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
<2009>
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
- Navigate by Thread:
- Prev:
Re: Remote I/O Bruce Hill
- Next:
Re: Remote I/O Bruce Hill
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
<2009>
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024