RE: IOC make error

["Mark Rivers" <rivers@cars.uchicago.edu>]

Those are the same settings I am using.

 

What version of Cygwin are you using?  What is the size and date of your /bin/make.exe?

 

Mark

 

 

---

From: Cid, Florencio A [mailto:florencio.a.cid@boeing.com]
Sent: Tuesday, November 08, 2011 10:04 AM
To: Mark Rivers; Ron Sluiter
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

Mark,

 

 

I’ve set the following in the file, CONFIG_SITE,

 

SHARED_LIBRARIES = NO

STATIC_BUILD = YES

 

Flo

 

From: Mark Rivers [mailto:rivers@cars.uchicago.edu]
Sent: Tuesday, November 08, 2011 8:30 AM
To: Ron Sluiter; Cid, Florencio A
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

I don’t think that tech-talk message of mine applies any more.  That was an attempt to use the Cygwin version of make to build for win32-x86.  That is not supported, and one should use the GnuWin version of make to build for win32-x86.  

 

As far as I know the current Cygwin version of make should work OK to build for the cygwin-x86 architecture, and there is no need to roll back to an earlier version.

 

Are you building statically or dynamically?

 

Mark

 

 

---

From: tech-talk-bounces@aps.anl.gov [mailto:tech-talk-bounces@aps.anl.gov] On Behalf Of Ron Sluiter
Sent: Tuesday, November 08, 2011 9:27 AM
To: Cid, Florencio A
Cc: 'tech-talk@aps.anl.gov'
Subject: Re: IOC make error

 

This tech-talk entry may fix your problem.

On 11/7/2011 4:42 PM, Cid, Florencio A wrote:

Hello all,

 

I’ve just installed EPICS base (3.14.12.1) on Windows XP with Cygwin (EPICS_HOST_ARCH = cygwin-x86).   To verify the installation, I was attempting to building the Example IOC application (per Section 2.2 of the Application Developer’s Guide). 

 

Unfortunately, I am encountering the following errors upon attempting to compile:

 

$ make

make -C ./configure install

make[1]: Entering directory `/cygdrive/c/mytop/configure'

make -C O.cygwin-x86 -f ../Makefile TOP=../.. T_A=cygwin-x86 install

make[2]: Entering directory `/cygdrive/c/mytop/configure/O.cygwin-x86'

perl c:/EPICS/base/bin/cygwin-x86/convertRelease.pl checkRelease

make[2]: Leaving directory `/cygdrive/c/mytop/configure/O.cygwin-x86'

make[1]: Leaving directory `/cygdrive/c/mytop/configure'

make -C ./myexampleApp install

make[1]: Entering directory `/cygdrive/c/mytop/myexampleApp'

make -C ./src install

make[2]: Entering directory `/cygdrive/c/mytop/myexampleApp/src'

make -C O.cygwin-x86 -f ../Makefile TOP=../../.. T_A=cygwin-x86 install

make[3]: Entering directory `/cygdrive/c/mytop/myexampleApp/src/O.cygwin-x86'

c:/EPICS/base/configure/RULES_TARGET:69: *** multiple target patterns.  Stop.

make[3]: Leaving directory `/cygdrive/c/mytop/myexampleApp/src/O.cygwin-x86'

make[2]: *** [install.cygwin-x86] Error 2

make[2]: Leaving directory `/cygdrive/c/mytop/myexampleApp/src'

make[1]: *** [src.install] Error 2

make[1]: Leaving directory `/cygdrive/c/mytop/myexampleApp'

make: *** [myexampleApp.install] Error 2

 

 

Not sure if this is an indication that I have a bad EPICS base build and/or have something lacking in my environment, etc.  Any help/info/assistance will be greatly appreciated. 

 

 

Thanks in advance,

 

Florencio Cid