1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 <2013> 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 | Index | 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 <2013> 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 |
<== Date ==> | <== Thread ==> |
---|
Subject: | RE: IP330 modules question |
From: | Mark Rivers <[email protected]> |
To: | "'Geon-Yeong Mun'" <[email protected]> |
Cc: | "[email protected]" <[email protected]> |
Date: | Tue, 4 Jun 2013 20:44:54 +0000 |
Hi, The first thing I see is that the output in the calibration routine generally looks correct. Here is the output of the log file you sent, where I grep for the string adj_offset: corvette:~/scratch>grep adj_offset log_04100114.log
2013/06/04 01:02:47.932 drvIp330::calibrate channel 0 adj_slope 9.983789e-01 adj_offset 4.389286e+01 2013/06/04 01:02:50.523 drvIp330::calibrate channel 1 adj_slope 9.983731e-01 adj_offset 4.392793e+01 2013/06/04 01:02:53.113 drvIp330::calibrate channel 2 adj_slope 9.983867e-01 adj_offset 4.332526e+01 2013/06/04 01:02:55.726 drvIp330::calibrate channel 3 adj_slope 9.983770e-01 adj_offset 4.348788e+01 2013/06/04 01:02:58.318 drvIp330::calibrate channel 4 adj_slope 9.983799e-01 adj_offset 4.379847e+01 2013/06/04 01:03:00.930 drvIp330::calibrate channel 5 adj_slope 9.983838e-01 adj_offset 4.385842e+01 2013/06/04 01:03:03.522 drvIp330::calibrate channel 6 adj_slope 9.983780e-01 adj_offset 4.395599e+01 2013/06/04 01:03:06.135 drvIp330::calibrate channel 7 adj_slope 9.983654e-01 adj_offset 4.430804e+01 2013/06/04 01:03:08.725 drvIp330::calibrate channel 8 adj_slope 9.983925e-01 adj_offset 4.307143e+01 2013/06/04 01:03:11.316 drvIp330::calibrate channel 9 adj_slope 9.983440e-01 adj_offset 4.547832e+01 2013/06/04 01:03:13.929 drvIp330::calibrate channel 10 adj_slope 9.983886e-01 adj_offset 4.329273e+01 2013/06/04 01:03:16.520 drvIp330::calibrate channel 11 adj_slope 9.983799e-01 adj_offset 4.364222e+01 2013/06/04 01:03:19.134 drvIp330::calibrate channel 12 adj_slope 9.983809e-01 adj_offset 4.354783e+01 2013/06/04 01:03:21.745 drvIp330::calibrate channel 13 adj_slope 9.983731e-01 adj_offset 4.395918e+01 2013/06/04 01:03:24.337 drvIp330::calibrate channel 14 adj_slope 9.983751e-01 adj_offset 4.402041e+01 2013/06/04 01:03:26.949 drvIp330::calibrate channel 15 adj_slope 9.983818e-01 adj_offset 4.335969e+01 2013/06/04 01:04:29.085 drvIp330::calibrate channel 0 adj_slope 9.983595e-01 adj_offset 4.453061e+01 2013/06/04 01:04:31.676 drvIp330::calibrate channel 1 adj_slope 9.983799e-01 adj_offset 4.392347e+01 2013/06/04 01:04:34.267 drvIp330::calibrate channel 2 adj_slope 9.983857e-01 adj_offset 4.345089e+01 2013/06/04 01:04:36.881 drvIp330::calibrate channel 3 adj_slope 9.983760e-01 adj_offset 4.392602e+01 2013/06/04 01:04:39.471 drvIp330::calibrate channel 4 adj_slope 9.983838e-01 adj_offset 4.373342e+01 2013/06/04 01:04:42.084 drvIp330::calibrate channel 5 adj_slope 9.983867e-01 adj_offset 4.351276e+01 2013/06/04 01:04:44.674 drvIp330::calibrate channel 6 adj_slope 9.983489e-01 adj_offset 4.510013e+01 2013/06/04 01:04:47.265 drvIp330::calibrate channel 7 adj_slope 9.983799e-01 adj_offset 4.407972e+01 2013/06/04 01:04:49.878 drvIp330::calibrate channel 8 adj_slope 9.983760e-01 adj_offset 4.411352e+01 2013/06/04 01:04:52.469 drvIp330::calibrate channel 9 adj_slope 9.983663e-01 adj_offset 4.415115e+01 2013/06/04 01:04:55.081 drvIp330::calibrate channel 10 adj_slope 9.983605e-01 adj_offset 4.440497e+01 2013/06/04 01:04:57.671 drvIp330::calibrate channel 11 adj_slope 9.983945e-01 adj_offset 4.275765e+01 2013/06/04 01:05:00.284 drvIp330::calibrate channel 12 adj_slope 9.983683e-01 adj_offset 4.471237e+01 2013/06/04 01:05:02.897 drvIp330::calibrate channel 13 adj_slope 9.983896e-01 adj_offset 4.372959e+01 2013/06/04 01:05:05.488 drvIp330::calibrate channel 14 adj_slope 9.983877e-01 adj_offset 4.360587e+01 2013/06/04 01:05:08.101 drvIp330::calibrate channel 15 adj_slope 9.983663e-01 adj_offset 4.430740e+01 2013/06/04 01:06:10.235 drvIp330::calibrate channel 0 adj_slope 1.031244e+00 adj_offset -2.027558e+03 2013/06/04 01:06:12.826 drvIp330::calibrate channel 1 adj_slope 9.983654e-01 adj_offset 4.446429e+01 2013/06/04 01:06:15.437 drvIp330::calibrate channel 2 adj_slope 9.983731e-01 adj_offset 4.392793e+01 2013/06/04 01:06:18.028 drvIp330::calibrate channel 3 adj_slope 9.983789e-01 adj_offset 4.401786e+01 2013/06/04 01:06:20.618 drvIp330::calibrate channel 4 adj_slope 9.983945e-01 adj_offset 4.310140e+01 2013/06/04 01:06:23.230 drvIp330::calibrate channel 5 adj_slope 9.983644e-01 adj_offset 4.455867e+01 2013/06/04 01:06:25.820 drvIp330::calibrate channel 6 adj_slope 9.983692e-01 adj_offset 4.393048e+01 2013/06/04 01:06:28.433 drvIp330::calibrate channel 7 adj_slope 9.983673e-01 adj_offset 4.415051e+01 2013/06/04 01:06:31.025 drvIp330::calibrate channel 8 adj_slope 9.983683e-01 adj_offset 4.446237e+01 2013/06/04 01:06:33.638 drvIp330::calibrate channel 9 adj_slope 9.983867e-01 adj_offset 4.332526e+01 2013/06/04 01:06:36.229 drvIp330::calibrate channel 10 adj_slope 9.983683e-01 adj_offset 4.427487e+01 2013/06/04 01:06:38.841 drvIp330::calibrate channel 11 adj_slope 9.983789e-01 adj_offset 4.367411e+01 2013/06/04 01:06:41.433 drvIp330::calibrate channel 12 adj_slope 9.983644e-01 adj_offset 4.446492e+01 2013/06/04 01:06:44.045 drvIp330::calibrate channel 13 adj_slope 9.983780e-01 adj_offset 4.367474e+01 2013/06/04 01:06:46.637 drvIp330::calibrate channel 14 adj_slope 9.983809e-01 adj_offset 4.370408e+01 2013/06/04 01:06:49.249 drvIp330::calibrate channel 15 adj_slope 9.983877e-01 adj_offset 4.304337e+01 Note that the slope is generally close of 0.9984 and the offset if about 44 A/D units. There is only 1 exception, which is this line: 2013/06/04 01:06:10.235 drvIp330::calibrate channel 0 adj_slope 1.031244e+00 adj_offset -2.027558e+03 During that calibration cycle you got the following output: 2013/06/04 01:06:08.202 drvIp330::calibrate. Raw values low channel=0 2013/06/04 01:06:08.202 0 65535 2013/06/04 01:06:08.202 1 32788 2013/06/04 01:06:08.202 2 32786 2013/06/04 01:06:08.202 3 32783 2013/06/04 01:06:08.202 4 32784 2013/06/04 01:06:08.202 5 32780 Note that the very first reading is wrong, it is 65535, not ~32780. This is either a hardware read problem, or perhaps not enough setting time. If you look at the driver code you will see that it actually reads the first value twice
to allow for settling, and maybe it needs an additional read. But the vale 65535 looks suspicious, because it is exactly 2^16-1, and none of the actual high-voltage calibration values are greater than 65000. We can ignore the calibration glitch for the time being. The problem as I understand it is that you have a 1.5 volt input signal, but the value measured by the IP330 is 2.66 volts. Is this correct? In the dbpr output you sent, EGUL=-5.0, EGUF=5.0, EOFF=-5.0 and ESLO=1.5259e-4. These all seem correct. RVAL=50159. The corresponding voltage is thus: VAL = -5.0 + 50159 * 1.5259e-4 = 2.65 volts. This is very close (but not identical) to the VAL field. So it seems like the unit is calibrating correctly, and it is converting RVAL to VAL OK. I don’t know why the RVAL value does not match what you expect for 1.5 V input. Are you sure you have wired up the unit correctly? Mark -----Original Message----- Hi Mark. Software version.... DEVIOCSTATS=/usr/local/epics/support/iocStats AUTOSAVE=/usr/local/epics/support/autosave-5-0 CAPUTLOG=/usr/local/epics/support/caPutLog-3.3.3 DEVLIB2=/usr/local/epics/support/devlib2 SNCSEQ=/usr/local/epics/support/seq-2.1.12 MRFIOC2=/usr/local/epics/support/mrfioc2 IPAC=/usr/local/epics/support/ipac-2.11 ASYN=/usr/local/epics/support/asyn4-21 IP330=/usr/local/epics/support/ip330R2-7 EPICS_BASE=/usr/local/epics/base-3.14.12.3 And, I attach the asynTrace log file. I had to think that data[] of intTask function in IP330 module was Raw-data. so, I had to debug it. I had to set the measuring range to -5~5voltage.(The setting of dip-switch of IP330 was same.). so, I think that, the 33453 was means approximate 0volt. and 65535 was means approximate 5volt. and, I think that this data is means in cailbration process. The value of epics channel access seems to result of moving average of data. If the data was result of calibration process, then It looks like a normal operation. However, the problem is that I can't check the raw-data(input voltage 1.5volt). at now, I'm not sure that this data is calibration data or Raw-data of the channel. I don't know that how to reads the input voltage(1.5 volt). Best regards. Geon-Yeong. -> dbpr ("13LAB:IP330_1","5") ACKS: INVALID ACKT: YES ADEL: 0
ALST: 2.6586556801709 AOFF: 0 ASG: ASLO: 1 ASP: 0x0 BKPT: 00 DESC: DISA: 0 DISP: 0 DISS: NO_ALARM DISV: 1 DPVT: 0x4b69a70 DSET: 0x4dd5c2c DTYP: asynInt32Average EGU: EGUF: 5 EGUL: -5 EOFF: -5 ESLO: 1.52590218966964e-04 EVNT: 0 FLNK:CONSTANT 0 HHSV: NO_ALARM HIGH: 0 HIHI: 0 HOPR: 5 HSV: NO_ALARM HYST: 0 INIT: 0
INP:INST_IO @asyn(IP330_1 0)DATA LALM: 2.65377279316396 LBRK: 0 LCNT: 0 LINR: LINEAR LLSV: NO_ALARM LOLO: 0 LOPR: -5 LOW: 0 LSET: 0x4b80dd0 LSV: NO_ALARM MDEL: 0 MLIS: 06 0a 10 20 06 0a 06 c0 00 00 00 06 MLOK: 04 f1 95 a0 MLST: 2.65377279316396 NAME: 13LAB:IP330_1 NSEV: NO_ALARM NSTA: NO_ALARM ORAW: 50159 PACT: 0 PBRK: 0x0 PHAS: 0 PINI: NO PPN: 0x0 PPNR: 0x0 PREC: 4 PRIO: LOW PROC: 0 PUTF: 0 RDES: 0x45a09d0 ROFF: 0 RPRO: 0 RSET: 0x4dd626c RVAL: 50159 SCAN: 1 second SDIS:CONSTANT SEVR: NO_ALARM SIML:CONSTANT SIMM: NO SIMS: NO_ALARM SIOL:CONSTANT SMOO: 0 SPVT: 0x6000d00 STAT: NO_ALARM SVAL: 0 TIME: 2013-06-04 05:33:59.178195571 TPRO: 0 TSE: 0 TSEL:CONSTANT UDF: 0 VAL: 2.6591134508278 value = 0 = 0x0 -> -----Original Message----- From: Mark Rivers [mailto:[email protected]]
Sent: Monday, June 03, 2013 10:21 PM To: Geon-Yeong Mun Subject: RE: IP330 modules question What version of the ip330 software are you using? The ip330::calibration function has an asynPrint statement to print the raw calibration values. Please set asynTrace to enable those messages so we can see what they are. Mark ________________________________________ From: Geon-Yeong Mun [[email protected]] Sent: Monday, June 03, 2013 1:14 AM To: Mark Rivers Subject: RE: IP330 modules question Yes. I added. Printf is show the Raw Data value and calibration factor. And, I using the internal power supply +-12v. J1,J2 jumper settings is equal. I don't know more about the interrupt vector. ipacAddXy9660("0000,4 A=2,800000") initIp330("IP330_1",0,0,"D","-5to5",0,15,4) interrupt vector value was not 4 then IP330 was print error message about vector. And AVME9670 link LED was not blink. Best regards. Geon-Yeong. -----Original Message----- From: Mark Rivers [mailto:[email protected]] Sent: Monday, June 03, 2013 11:54 AM To: Geon-Yeong Mun;
[email protected] Subject: RE: IP330 modules question Are the debugging print statements you show ones that you have added? What voltage source are you using for the IP330, the internal +-12V, or external +-15V? Are you sure that interrupt vector 4 is correct? The VoltCALLO values seem to be jumping all over the place in the calibration routine. Mark ________________________________ From: [email protected] [[email protected]] on behalf of Geon-Yeong Mun [[email protected]] Sent: Sunday, June 02, 2013 9:19 PM Subject: IP330 modules question Hi all. I tried to run IP300 module, and read the Analog data. All Raw data(16ch Diff mode) are displayed as shown below. This data's source is 5 voltage. Data: 65535 Data: 65535 Data: 50845 Data: 33453 Data: 65535 Data: 65535 Data: 33454 Data: 33453 Data: 33450 Data: 65535 Data: 65535 Data: 33452 Data: 33452 Data: 33453 Data: 65535 Data: 65535 Data: 33452 Data: 33453 Data: 65535 Data: 65535 Data: 65535 Data: 33451 Data: 33454 Data: 65535 Data: 65535 Data: 65535 This repeating pattern is the 33453 and 65535 Are you known about this? Development environment Epics base: 3.14.12.3 Target os : vxWorks 6.9 Hardware : AVME9670, IP330A Modules : ipac 2.11, ip330 Best regards. Geon-Yeong ----------------------------------------------------------------------- boot device : geisc unit number : 0 processor number : 0 host name : gymun-evr file name : /home/work/image/vxWorks inet on ethernet (e) : 141.223.48.53:ffffff00 host inet (h) : 141.223.48.51 gateway inet (g) : 141.223.48.99 user (u) : work ftp password (pw) : work flags (f) : 0x0 target name (tn) : evrTest startup script (s) : /home/work/st.vxWorks.evr Loading... 2354032 Starting at 0x100000... Loading symbol table from gymun-evr:/home/work/image/vxWorks.sym ...done VxWorks Copyright 1984-2013 Wind River Systems, Inc. CPU: Motorola MVME6100-0173 - MPC 7457 Runtime Name: VxWorks Runtime Version: 6.9 BSP version: 6.9/0 Created: May 23 2013, 18:22:53 ED&R Policy Mode: Deployed WDB Comm Type: WDB_COMM_END WDB: Ready. Executing startup script '/home/work/st.vxWorks.evr'... #================ ipAttach(1,"geisc") value = 0 = 0x0 ifconfig("geisc1 inet 192.168.10.131 netmask 255.255.255.0 up") value = 0 = 0x0 tyBackspaceSet(0177) value = 127 = 0x7f #ld < mrf.munch ld < mrfTest.munch value = 72237072 = 0x44e4010 # env setting epicsEnvSet("ENGINEER","Geon-Yeong Mun") value = 0 = 0x0 epicsEnvSet("LOCATION","TestLab") value = 0 = 0x0 epicsEnvSet("EPICS_CA_MAX_ARRAY_BYTES","1000000") value = 0 = 0x0 epicsEnvSet("EPICS_TS_NTP_INET","141.223.48.51") value = 0 = 0x0 #dbLoadDatabase("dbd/mrf.dbd",0,0) #mrf_registerRecordDeviceDriver(pdbbase) dbLoadDatabase("dbd/mrfTest.dbd",0,0) value = 0 = 0x0 mrfTest_registerRecordDeviceDriver(pdbbase) value = 0 = 0x0 # IRQ 3: EVR # IRQ 4: AVME9670 # EVG(A24) #mrmEvgSetupVME("EVG1",2,0x00050000,4,0xc0) #mrmEvgSetupVME("EVG1",2,0x00000000,4,0xc0) # sysBusToLocalAdrs(0x0d,0x00100000,&a)Can't reg ister 'system' comm and -- no command i# EVR(A24)nterpreter available. #mrmEvrSetupVME("EVR1",5,0x00100000,3,0x26) #mrmEvrSetupVME("EVR1",5,0x00200000,4,0x24) #mrmEvrSetupVME("EVR1",5,0x08000000,3,0x26) mrmEvrSetupVME("EVR1",2,0x00000000,3,0x26) Setting up EVR in VME Slot 2 Found vendor: 00000eb2 board: 455246e6 rev.: 00000000 EVR check. EVR-230 'EVR1' slot 2 FPGA version... 0006 Found SFP Strangeness ffffffff FWVersVME64 ion 0x12000006Out FP: 7 FPUNIV:4 RB:Found version 6 16 IFP:2 Using IRQ 35:38EVR FIFO task start value = 0 = 0x0 # sysBusToLocalAdrs(0x0d,0x00280000,&k) # sysBusToLocalAdrs(0x0d,0x00300000,&k) # # 0xF8 : 7C00000 # ACROMAG AVME9670 ipacAddXy9660("0000,4 A=2,800000") Now finish parsing.... A=2,800000 AVME-IP: init success...1 value = 0 = 0x0 # ACROMAG IP330 # string : portName # int carrierID # int SlotID # string type : "D" or "S" for differential or single-ended # string range # int firstChan # int lastChan # int interruptVector #initIp330("IP330_1",0,0,"D","-5to5",0,15,4) initIp330("IP330_1",0,0,"D","-5to5",0,15,4) value = 0 = 0x0 configIp330("IP330_1",3,"Input",1000,60) ########### CALIBRATION ######## CH 00 Corrected_Count: 1.019773 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.968750 CountCALLO: 33451.968750 drvIp330::calibrate channel 0 adj_slope 1.019773e+00 adj_offset -1.319316e+03 ########### CALIBRATION ######## CH 01 Corrected_Count: 1.018058 Ideal_Volt_Span: 10.000000 m: 0.000155 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.718750 CountCALLO: 33398.687500 drvIp330::calibrate channel 1 adj_slope 1.018058e+00 adj_offset -1.211921e+03 ########### CALIBRATION ######## CH 02 Corrected_Count: -54.189974 Ideal_Volt_Span: 10.000000 m: -0.008269 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.406250 CountCALLO: 65535.000000 drvIp330::calibrate channel 2 adj_slope -5.418997e+01 adj_offset -6.613969e+04 ########### CALIBRATION ######## CH 03 Corrected_Count: -54.178546 Ideal_Volt_Span: 10.000000 m: -0.008267 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.281250 CountCALLO: 65535.000000 drvIp330::calibrate channel 3 adj_slope -5.417855e+01 adj_offset -6.613982e+04 ########### CALIBRATION ######## CH 04 Corrected_Count: 2.016120 Ideal_Volt_Span: 10.000000 m: 0.000308 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.843750 CountCALLO: 49013.906250 drvIp330::calibrate channel 4 adj_slope 2.016120e+00 adj_offset -3.276091e+04 ########### CALIBRATION ######## CH 05 Corrected_Count: -54.189974 Ideal_Volt_Span: 10.000000 m: -0.008269 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.406250 CountCALLO: 65535.000000 drvIp330::calibrate channel 5 adj_slope -5.418997e+01 adj_offset -6.613969e+04 ########### CALIBRATION ######## CH 06 Corrected_Count: 1.019771 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.250000 CountCALLO: 33452.187500 drvIp330::calibrate channel 6 adj_slope 1.019771e+00 adj_offset -1.319471e+03 ########### CALIBRATION ######## CH 07 Corrected_Count: 1.021627 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.968750 CountCALLO: 33509.125000 drvIp330::calibrate channel 7 adj_slope 1.021627e+00 adj_offset -1.434795e+03 ########### CALIBRATION ######## CH 08 Corrected_Count: -54.149996 Ideal_Volt_Span: 10.000000 m: -0.008263 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.968750 CountCALLO: 65535.000000 drvIp330::calibrate channel 8 adj_slope -5.415000e+01 adj_offset -6.614013e+04 ########### CALIBRATION ######## CH 09 Corrected_Count: 1.019775 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.843750 CountCALLO: 33451.906250 drvIp330::calibrate channel 9 adj_slope 1.019775e+00 adj_offset -1.319317e+03 ########### CALIBRATION ######## CH 10 Corrected_Count: 1.063591 Ideal_Volt_Span: 10.000000 m: 0.000162 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.437500 CountCALLO: 34749.781250 drvIp330::calibrate channel 10 adj_slope 1.063591e+00 adj_offset -3.940948e+03 ########### CALIBRATION ######## CH 11 Corrected_Count: 11.663407 Ideal_Volt_Span: 10.000000 m: 0.001780 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.625000 CountCALLO: 62189.343750 drvIp330::calibrate channel 11 adj_slope 1.166341e+01 adj_offset -5.937987e+04 ########### CALIBRATION ######## CH 12 Corrected_Count: 1.019800 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.875000 CountCALLO: 33452.718750 drvIp330::calibrate channel 12 adj_slope 1.019800e+00 adj_offset -1.320927e+03 ########### CALIBRATION ######## CH 13 Corrected_Count: 1.019208 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.031250 CountCALLO: 33434.593750 drvIp330::calibrate channel 13 adj_slope 1.019208e+00 adj_offset -1.284147e+03 ########### CALIBRATION ######## CH 14 Corrected_Count: -54.147143 Ideal_Volt_Span: 10.000000 m: -0.008262 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.937500 CountCALLO: 65535.000000 drvIp330::calibrate channel 14 adj_slope -5.414714e+01 adj_offset -6.614017e+04 ########### CALIBRATION ######## CH 15 Corrected_Count: 1.020357 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.968750 CountCALLO: 33470.000000 drvIp330::calibrate channel 15 adj_slope 1.020357e+00 adj_offset -1.355746e+03 ########### CALIBRATION ######## CH 00 Corrected_Count: -54.158558 Ideal_Volt_Span: 10.000000 m: -0.008264 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.062500 CountCALLO: 65535.000000 drvIp330::calibrate channel 0 adj_slope -5.415856e+01 adj_offset -6.614004e+04 ########### CALIBRATION ######## CH 01 Corrected_Count: -54.144290 Ideal_Volt_Span: 10.000000 m: -0.008262 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.906250 CountCALLO: 65535.000000 drvIp330::calibrate channel 1 adj_slope -5.414429e+01 adj_offset -6.614020e+04 ########### CALIBRATION ######## CH 02 Corrected_Count: 1.019775 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.812500 CountCALLO: 33451.875000 drvIp330::calibrate channel 2 adj_slope 1.019775e+00 adj_offset -1.319286e+03 ########### CALIBRATION ######## CH 03 Corrected_Count: -142.248682 Ideal_Volt_Span: 10.000000 m: -0.021705 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.250000 CountCALLO: 65168.000000 drvIp330::calibrate channel 3 adj_slope -1.422487e+02 adj_offset -6.539836e+04 ########### CALIBRATION ######## CH 04 Corrected_Count: 1.678135 Ideal_Volt_Span: 10.000000 m: 0.000256 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.875000 CountCALLO: 45805.968750 drvIp330::calibrate channel 4 adj_slope 1.678135e+00 adj_offset -2.627953e+04 ########### CALIBRATION ######## CH 05 Corrected_Count: 1.019750 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.156250 CountCALLO: 33451.468750 drvIp330::calibrate channel 5 adj_slope 1.019750e+00 adj_offset -1.318114e+03 ########### CALIBRATION ######## CH 06 Corrected_Count: -54.175690 Ideal_Volt_Span: 10.000000 m: -0.008267 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.250000 CountCALLO: 65535.000000 drvIp330::calibrate channel 6 adj_slope -5.417569e+01 adj_offset -6.613985e+04 ########### CALIBRATION ######## CH 07 Corrected_Count: 11.856519 Ideal_Volt_Span: 10.000000 m: 0.001809 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.031250 CountCALLO: 62233.593750 drvIp330::calibrate channel 7 adj_slope 1.185652e+01 adj_offset -5.946988e+04 ########### CALIBRATION ######## CH 08 Corrected_Count: -54.187117 Ideal_Volt_Span: 10.000000 m: -0.008268 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.375000 CountCALLO: 65535.000000 drvIp330::calibrate channel 8 adj_slope -5.418712e+01 adj_offset -6.613972e+04 ########### CALIBRATION ######## CH 09 Corrected_Count: -54.175690 Ideal_Volt_Span: 10.000000 m: -0.008267 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.250000 CountCALLO: 65535.000000 drvIp330::calibrate channel 9 adj_slope -5.417569e+01 adj_offset -6.613985e+04 ########### CALIBRATION ######## CH 10 Corrected_Count: 1.019763 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.031250 CountCALLO: 33451.718750 drvIp330::calibrate channel 10 adj_slope 1.019763e+00 adj_offset -1.318747e+03 ########### CALIBRATION ######## CH 11 Corrected_Count: -66.207363 Ideal_Volt_Span: 10.000000 m: -0.010102 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.781250 CountCALLO: 65426.812500 drvIp330::calibrate channel 11 adj_slope -6.620736e+01 adj_offset -6.592174e+04 ########### CALIBRATION ######## CH 12 Corrected_Count: 1.014113 Ideal_Volt_Span: 10.000000 m: 0.000155 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.937500 CountCALLO: 33276.187500 drvIp330::calibrate channel 12 adj_slope 1.014113e+00 adj_offset -9.641977e+02 ########### CALIBRATION ######## CH 13 Corrected_Count: 1.019767 Ideal_Volt_Span: 10.000000 m: 0.000156 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.031250 CountCALLO: 33451.843750 drvIp330::calibrate channel 13 adj_slope 1.019767e+00 adj_offset -1.318999e+03 ########### CALIBRATION ######## CH 14 Corrected_Count: -54.164267 Ideal_Volt_Span: 10.000000 m: -0.008265 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64942.125000 CountCALLO: 65535.000000 drvIp330::calibrate channel 14 adj_slope -5.416427e+01 adj_offset -6.613997e+04 ########### CALIBRATION ######## CH 15 Corrected_Count: 9.344492 Ideal_Volt_Span: 10.000000 m: 0.001426 Gain: 1.000000 VoltCALHI: 4.900000 VoltCALLO: 0.000000 CountCALHI: 64941.906250 CountCALLO: 61505.375000 drvIp330::calibrate channel 15 adj_slope 9.344492e+00 adj_offset -5.799871e+04 value = 0 = 0x0 Data: # EVG db #dbLoadRecords("db/vme-evg230.db", "SYS=TST, D=evg:1, EVG=EVG1") 64694 # BNL specific timing sequence constructor #dbLoadRecords("db/nsls2-inj-seqs.db","LN=LN-TS, BR=BR-TS, INJ=TST, EVG=evg:1, SEQ=SoftSeq:0")Data: # EVR # 33452dbLoadRecords("db/evr-vmerf-230.db","SYS=TST, D=evr:1, EVR=EVR1") Data: 33451 Data: 33452 Data: 33454 Data: 33453 Data: 33452 Data: 3value = 0 = 0x0 # IP330 # dbLoadTemplate("db/ip330Scan.substitutions") 3448 Data: 36040 Data: 64906 Data: 63022 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 41509 Data: 33451 Data: 33453 Data: 33452 Data: 33452 Data: 33451 Data: 33451 Data: 33452 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 33456 Data: 33451 Data: 33451 Data: 33452 Data: 33451 Data: 33453 Data: 33451 Data: 33453 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 33454 Data: 33452 Data: 334value = 520 = 0x0 dbLoadRecords("db/iocAdminVxWorks.db", "IOC=evrTest")Data: 33452 Data: 33452 Data: 3345value = 0 = 0x0 iocInit()Data: Starting iocInit 65535#### ###################Data: ##############65535############### ###################Data: ##### ## EPICS65535 R3.14.12.3 $Da te: Mon 2012-12-17 Data: 14:11:47 -060065535$ ## EPICS Base built May 14 2013 Data: ##############65535############### ###################Data: ##############65535############## Data: 45663 Data: 33452 Data: 33452 Data: 33452 Data: 33451 Data: 33452 Data: 33453 Data: 33451 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 65535 Data: 33456 Data: 33451 Data: 33451 Data: 33452 |