RE: IOC make error

["Cid, Florencio A" <florencio.a.cid@boeing.com>]

Mark,

 

Using the make.exe received from you, I was able to get successfully compile the example IOC, but encountered the following (see below).

 

$ make clean

make -C ./configure clean

make[1]: Entering directory `/cygdrive/c/mytop/configure'

rm -rf O.cygwin-x86 O.Common

make[1]: Leaving directory `/cygdrive/c/mytop/configure'

make -C ./myexampleApp clean

make[1]: Entering directory `/cygdrive/c/mytop/myexampleApp'

make -C ./src clean

make[2]: Entering directory `/cygdrive/c/mytop/myexampleApp/src'

rm -rf O.cygwin-x86 O.Common

make[2]: Leaving directory `/cygdrive/c/mytop/myexampleApp/src'

make -C ./Db clean

make[2]: Entering directory `/cygdrive/c/mytop/myexampleApp/Db'

rm -rf O.cygwin-x86 O.Common

make[2]: Leaving directory `/cygdrive/c/mytop/myexampleApp/Db'

make[1]: Leaving directory `/cygdrive/c/mytop/myexampleApp'

make -C ./iocBoot clean

make[1]: Entering directory `/cygdrive/c/mytop/iocBoot'

make -C ./iocmyexample clean

make[2]: Entering directory `/cygdrive/c/mytop/iocBoot/iocmyexample'

rm -f cdCommands envPaths dllPath.bat

make[2]: Leaving directory `/cygdrive/c/mytop/iocBoot/iocmyexample'

make[1]: Leaving directory `/cygdrive/c/mytop/iocBoot'

 

ui495a@lt-fcid /cygdrive/c/mytop

$ make

make -C ./configure install

make[1]: Entering directory `/cygdrive/c/mytop/configure'

perl c:/EPICS/base/bin/cygwin-x86/makeMakefile.pl O.cygwin-x86 ../..

mkdir O.Common

make -C O.cygwin-x86 -f ../Makefile TOP=../.. T_A=cygwin-x86 install

make[2]: Entering directory `/cygdrive/c/mytop/configure/O.cygwin-x86'

perl c:/EPICS/base/bin/cygwin-x86/convertRelease.pl checkRelease

make[2]: Leaving directory `/cygdrive/c/mytop/configure/O.cygwin-x86'

make[1]: Leaving directory `/cygdrive/c/mytop/configure'

make -C ./myexampleApp install

make[1]: Entering directory `/cygdrive/c/mytop/myexampleApp'

make -C ./src install

make[2]: Entering directory `/cygdrive/c/mytop/myexampleApp/src'

perl c:/EPICS/base/bin/cygwin-x86/makeMakefile.pl O.cygwin-x86 ../../..

mkdir O.Common

make -C O.cygwin-x86 -f ../Makefile TOP=../../.. T_A=cygwin-x86 install

make[3]: Entering directory `/cygdrive/c/mytop/myexampleApp/src/O.cygwin-x86'

perl c:/EPICS/base/bin/cygwin-x86/makeIncludeDbd.pl base.dbd xxxSupport.dbd dbSu

bExample.dbd myexampleHello.dbd initTrace.dbd ../O.Common/myexampleInclude.dbd

Expanding dbd

Installing created dbd file ../../../dbd/myexample.dbd

c:/EPICS/base/bin/cygwin-x86/dbToRecordtypeH.exe  -I . -I .. -I ../../../dbd -Ic

:/EPICS/base/dbd  ../xxxRecord.dbd ../O.Common/xxxRecord.h

Installing generated generic include file ../../../include/xxxRecord.h

 

gcc -c  -D_POSIX_THREADS -D_POSIX_TIMERS            -DUNIX  -DCYGWIN32     -O3

 -Wall      -m32   -DEPICS_DLL_NO   -MMD -I. -I../O.Common -I. -I.. -I../../../i

nclude/os/cygwin32 -I../../../include -Ic:/EPICS/base/include/os/cygwin32 -Ic:/E

PICS/base/include       ../xxxRecord.c

 

gcc -c  -D_POSIX_THREADS -D_POSIX_TIMERS            -DUNIX  -DCYGWIN32     -O3

 -Wall      -m32   -DEPICS_DLL_NO   -MMD -I. -I../O.Common -I. -I.. -I../../../i

nclude/os/cygwin32 -I../../../include -Ic:/EPICS/base/include/os/cygwin32 -Ic:/E

PICS/base/include       ../devXxxSoft.c

 

gcc -c  -D_POSIX_THREADS -D_POSIX_TIMERS            -DUNIX  -DCYGWIN32     -O3

 -Wall      -m32   -DEPICS_DLL_NO   -MMD -I. -I../O.Common -I. -I.. -I../../../i

nclude/os/cygwin32 -I../../../include -Ic:/EPICS/base/include/os/cygwin32 -Ic:/E

PICS/base/include       ../dbSubExample.c

 

gcc -c  -D_POSIX_THREADS -D_POSIX_TIMERS            -DUNIX  -DCYGWIN32     -O3

 -Wall      -m32   -DEPICS_DLL_NO   -MMD -I. -I../O.Common -I. -I.. -I../../../i

nclude/os/cygwin32 -I../../../include -Ic:/EPICS/base/include/os/cygwin32 -Ic:/E

PICS/base/include       ../myexampleHello.c

 

gcc -c  -D_POSIX_THREADS -D_POSIX_TIMERS            -DUNIX  -DCYGWIN32     -O3

 -Wall      -m32   -DEPICS_DLL_NO   -MMD -I. -I../O.Common -I. -I.. -I../../../i

nclude/os/cygwin32 -I../../../include -Ic:/EPICS/base/include/os/cygwin32 -Ic:/E

PICS/base/include       ../initTrace.c

ar -rc   myexampleSupport.lib        xxxRecord.o devXxxSoft.o dbSubExample.o mye

xampleHello.o initTrace.o

ranlib myexampleSupport.lib

Installing library ../../../lib/cygwin-x86/myexampleSupport.lib

perl c:/EPICS/base/bin/cygwin-x86/registerRecordDeviceDriver.pl ../O.Common/myex

ample.dbd myexample_registerRecordDeviceDriver c\:/mytop > myexample.tmp

mv myexample.tmp myexample_registerRecordDeviceDriver.cpp

 

g++ -c  -D_POSIX_THREADS -D_POSIX_TIMERS            -DUNIX  -DCYGWIN32     -O3

 -Wall      -m32   -DEPICS_DLL_NO   -MMD -I. -I../O.Common -I. -I.. -I../../../i

nclude/os/cygwin32 -I../../../include -Ic:/EPICS/base/include/os/cygwin32 -Ic:/E

PICS/base/include       myexample_registerRecordDeviceDriver.cpp

 

g++ -c  -D_POSIX_THREADS -D_POSIX_TIMERS            -DUNIX  -DCYGWIN32     -O3

 -Wall      -m32   -DEPICS_DLL_NO   -MMD -I. -I../O.Common -I. -I.. -I../../../i

nclude/os/cygwin32 -I../../../include -Ic:/EPICS/base/include/os/cygwin32 -Ic:/E

PICS/base/include       ../myexampleMain.cpp

g++ -o myexample.exe -static -Lc\:/mytop/lib/cygwin-x86 -Lc\:/EPICS/base/lib/cyg

win-x86       -m32               myexample_registerRecordDeviceDriver.o myexampl

eMain.o    -lmyexampleSupport -lrecIoc -lsoftDevIoc -lmiscIoc -lrsrvIoc -ldbtool

sIoc -lasIoc -ldbIoc -lregistryIoc -ldbStaticIoc -lca -lCom   -lpthread   -lread

line -lcurses -lm

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -lmyexampleSupport

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -lrecIoc

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -lsoftDevIoc

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -lmiscIoc

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -lrsrvIoc

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -ldbtoolsIoc

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -lasIoc

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -ldbIoc

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -lregistryIoc

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -ldbStaticIoc

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -lca

/usr/lib/gcc/i686-pc-cygwin/4.5.3/../../../../i686-pc-cygwin/bin/ld: cannot find

 -lCom

collect2: ld returned 1 exit status

make[3]: *** [myexample.exe] Error 1

make[3]: Leaving directory `/cygdrive/c/mytop/myexampleApp/src/O.cygwin-x86'

make[2]: *** [install.cygwin-x86] Error 2

make[2]: Leaving directory `/cygdrive/c/mytop/myexampleApp/src'

make[1]: *** [src.install] Error 2

make[1]: Leaving directory `/cygdrive/c/mytop/myexampleApp'

make: *** [myexampleApp.install] Error 2

 

 

Flo 

 

 

From: Mark Rivers [mailto:rivers@cars.uchicago.edu]
Sent: Tuesday, November 08, 2011 10:37 AM
To: Cid, Florencio A; Ron Sluiter
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

No, I think if base built OK then you can proceed to building the IOC.

 

---

From: Cid, Florencio A [mailto:florencio.a.cid@boeing.com]
Sent: Tuesday, November 08, 2011 11:34 AM
To: Mark Rivers; Ron Sluiter
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

Thanks, Mark.    Will do.   Should I attempt to rebuild EPICS base with this new make.exe prior to trying to compile/build the example IOC? 

 

Flo

 

From: Mark Rivers [mailto:rivers@cars.uchicago.edu]
Sent: Tuesday, November 08, 2011 10:33 AM
To: Cid, Florencio A; Ron Sluiter
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

http://cars.uchicago.edu/software/pub/make.gz

 

gunzip it, and rename it from make to make.exe.

 

Mark

 

 

---

From: Cid, Florencio A [mailto:florencio.a.cid@boeing.com]
Sent: Tuesday, November 08, 2011 11:28 AM
To: Mark Rivers; Ron Sluiter
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

Mark,

 

I tend to agree with you regarding figuring out why the latest version of Cygwin make is not working…..  

 

In the meantime, I was wondering if you could please have a copy of your make.gz.   Thought that I would give it a try.  

 

 

Flo

 

 

From: Mark Rivers [mailto:rivers@cars.uchicago.edu]
Sent: Tuesday, November 08, 2011 9:41 AM
To: Cid, Florencio A; Ron Sluiter
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

Interestingly I see the following:

 

$ uname -r

1.7.7(0.230/5/3)

 

$ ls -al /bin/make*

-rwx------+ 1 epics  None     495190 2008-05-23 17:48 /bin/make.exe

-rwxr-x---+ 1 epics  Users    151552 2008-02-09 13:50 /bin/make.exe.old

-rw-r--r--  1 rivers mkpasswd 179495 2009-01-12 14:03 /bin/make.gz

 

So my version of Cygwin is slightly older than yours, 1.7.7 vs 1.7.9.  I have the same version of make as you which I am NOT using, (it is renamed to make.exe.old) and I am using another version that is about 3 times larger.  I honestly don’t remember where I got the version that I am using.  But the .gz file expands into the version of make.exe that I am using.  I can make that available if you want, but I think we need to figure out why the latest version of Cygwin make is not working?

 

Mark

 

 

 

---

From: Cid, Florencio A [mailto:florencio.a.cid@boeing.com]
Sent: Tuesday, November 08, 2011 10:26 AM
To: Mark Rivers; Ron Sluiter
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

Mark,

 

Cgwin version is as follows:

$ uname -r

1.7.9(0.237/5/3)

 

 

Info for /bin/make is as follows:

$ ls -al make

-rwxr-xr-x 1 ui495a root 151552 Feb  9  2008 make

 

 

Flo

 

From: Mark Rivers [mailto:rivers@cars.uchicago.edu]
Sent: Tuesday, November 08, 2011 9:18 AM
To: Cid, Florencio A; Ron Sluiter
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

Those are the same settings I am using.

 

What version of Cygwin are you using?  What is the size and date of your /bin/make.exe?

 

Mark

 

 

---

From: Cid, Florencio A [mailto:florencio.a.cid@boeing.com]
Sent: Tuesday, November 08, 2011 10:04 AM
To: Mark Rivers; Ron Sluiter
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

Mark,

 

 

I’ve set the following in the file, CONFIG_SITE,

 

SHARED_LIBRARIES = NO

STATIC_BUILD = YES

 

Flo

 

From: Mark Rivers [mailto:rivers@cars.uchicago.edu]
Sent: Tuesday, November 08, 2011 8:30 AM
To: Ron Sluiter; Cid, Florencio A
Cc: tech-talk@aps.anl.gov
Subject: RE: IOC make error

 

I don’t think that tech-talk message of mine applies any more.  That was an attempt to use the Cygwin version of make to build for win32-x86.  That is not supported, and one should use the GnuWin version of make to build for win32-x86.  

 

As far as I know the current Cygwin version of make should work OK to build for the cygwin-x86 architecture, and there is no need to roll back to an earlier version.

 

Are you building statically or dynamically?

 

Mark

 

 

---

From: tech-talk-bounces@aps.anl.gov [mailto:tech-talk-bounces@aps.anl.gov] On Behalf Of Ron Sluiter
Sent: Tuesday, November 08, 2011 9:27 AM
To: Cid, Florencio A
Cc: 'tech-talk@aps.anl.gov'
Subject: Re: IOC make error

 

This tech-talk entry may fix your problem.

On 11/7/2011 4:42 PM, Cid, Florencio A wrote:

Hello all,

 

I’ve just installed EPICS base (3.14.12.1) on Windows XP with Cygwin (EPICS_HOST_ARCH = cygwin-x86).   To verify the installation, I was attempting to building the Example IOC application (per Section 2.2 of the Application Developer’s Guide). 

 

Unfortunately, I am encountering the following errors upon attempting to compile:

 

$ make

make -C ./configure install

make[1]: Entering directory `/cygdrive/c/mytop/configure'

make -C O.cygwin-x86 -f ../Makefile TOP=../.. T_A=cygwin-x86 install

make[2]: Entering directory `/cygdrive/c/mytop/configure/O.cygwin-x86'

perl c:/EPICS/base/bin/cygwin-x86/convertRelease.pl checkRelease

make[2]: Leaving directory `/cygdrive/c/mytop/configure/O.cygwin-x86'

make[1]: Leaving directory `/cygdrive/c/mytop/configure'

make -C ./myexampleApp install

make[1]: Entering directory `/cygdrive/c/mytop/myexampleApp'

make -C ./src install

make[2]: Entering directory `/cygdrive/c/mytop/myexampleApp/src'

make -C O.cygwin-x86 -f ../Makefile TOP=../../.. T_A=cygwin-x86 install

make[3]: Entering directory `/cygdrive/c/mytop/myexampleApp/src/O.cygwin-x86'

c:/EPICS/base/configure/RULES_TARGET:69: *** multiple target patterns.  Stop.

make[3]: Leaving directory `/cygdrive/c/mytop/myexampleApp/src/O.cygwin-x86'

make[2]: *** [install.cygwin-x86] Error 2

make[2]: Leaving directory `/cygdrive/c/mytop/myexampleApp/src'

make[1]: *** [src.install] Error 2

make[1]: Leaving directory `/cygdrive/c/mytop/myexampleApp'

make: *** [myexampleApp.install] Error 2

 

 

Not sure if this is an indication that I have a bad EPICS base build and/or have something lacking in my environment, etc.  Any help/info/assistance will be greatly appreciated. 

 

 

Thanks in advance,

 

Florencio Cid