1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 <2019> 2020 2021 2022 2023 2024 | Index | 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 <2019> 2020 2021 2022 2023 2024 |
<== Date ==> | <== Thread ==> |
---|
Subject: | RE: [motorPIGCS2] can't turn on servo state of PI E-712 |
From: | Chiang, Liang-Chih [江良志] via Tech-talk <[email protected]> |
To: | "[email protected]" <[email protected]> |
Date: | Mon, 5 Aug 2019 03:14:27 +0000 |
Hi, Allan,
I used motor module(version 6.9) with the content of motorApp/PIGCS2Src replaced by motorPIGCS2 (https://github.com/epics-motor/motorPIGCS2).
After changed to motor module version 6.11, the error message "GCS error, Controller was stopped by command" disappeared. However, I still can't control PI E-712.
If I use motor module version 6.11, there will be error message about GCS error code 5:
2019/08/05 10:52:37.836 PIGCSController::getGCSError() GCS error, Unallowable move attempted on unreferenced axis, or move attempted with servo off 2019/08/05 10:52:37.836 Could not set servo state! If I use motor module version 6.11 with patch from Allan, there will be error mesaage about GCS error code 5 and 17: 2019/08/05 10:39:47.253 PIGCSController::getGCSError() GCS error code = 5 2019/08/05 10:39:47.253 PIGCSController::getGCSError() GCS error, Unallowable move attempted on unreferenced axis, or move attempted with servo off 2019/08/05 10:39:47.253 Could not set servo state! 2019/08/05 10:39:47.261 PIGCSController::setAxisPosition() sent "RON 1 0" 2019/08/05 10:39:47.261 PIGCSController::setAxisPosition() sent "POS 1 1937869.000000" 2019/08/05 10:39:47.261 PIGCSController::setAxisPosition() sent "RON 1 1" 2019/08/05 10:39:47.267 PIGCSController::getGCSError() GCS error code = 17 2019/08/05 10:39:47.267 PIGCSController::getGCSError() GCS error, Parameter out of range 2019/08/05 10:39:47.267 PIGCSController::setAxisPosition() failed, GCS error 17 If I issue GCS commands "FRF" and "SVO 1 1" before starting IOC, the CSS(Control-System Studio) interface of motor record will show:
https://www.dropbox.com/s/yrx7sikta3cqwzy/controller_error_PIE712.png?dl=0
Still fighting againt PI E-712, any suggestions are welcome.
Best regards. LiangChih Chiang National Synchrotron Radiation Research Center (NSRRC)
寄件者: Allan Serra Braga Bugyi <[email protected]>
寄件日期: 2019年8月2日 下午 08:44 收件者: [email protected]; Chiang, Liang-Chih [江良志] 主旨: RE: [motorPIGCS2] can't turn on servo state of PI E-712
Which motor record version are you using? I also had this problem, because the motor record was sending repeatedly HALT commands to the controller. Using motor record version 6-11 this behavior disappears.
Best regards,
Allan S. B. Bugyi Technology Development Analyst [email protected] (+55 19) 3512-3520 SOL/Beamline Software Group Brazilian Synchrotron Light Laboratory (LNLS) Center of Research in Energy and Materials (CNPEM) http://lnls.cnpem.br De: [email protected] <[email protected]> em nome de Chiang, Liang-Chih [江良志] via Tech-talk <[email protected]>
Enviado: quinta-feira, 1 de agosto de 2019 22:12 Para: [email protected] <[email protected]> Assunto: RE: [motorPIGCS2] can't turn on servo state of PI E-712 Hi, Allan,
I tried, but the IOC will issue the following error messages repeatedly.
2019/08/01 10:21:19.114 PIGCSController::getGCSError() GCS error code = 10
I'm still tracing the source code in motorPIGCS2.
Best regards.
LiangChih Chiang National Synchrotron Radiation Research Center (NSRRC)
寄件者: Allan Serra Braga Bugyi <[email protected]>
寄件日期: 2019年8月1日 下午 08:43 收件者: [email protected]; Chiang, Liang-Chih [江良志] 主旨: RE: [motorPIGCS2] can't turn on servo state of PI E-712
Hi LiangChih,
So it calls the 'setAxisPosition' method from 'PIGCSController' class, passing the parameter 'm_positionCts' (the current position), which holds the result of POS? command. The 'PIGCSController::setAxisPosition' sends RON command with parameter
0 (to set closed loop off), then POS command with the current position, then RON command with parameter 1 (to set closed loop on).
There are some controllers that doesn't recognize RON command, which is not a problem.
Best regards,
Allan S. B. Bugyi Technology Development Analyst [email protected] (+55 19) 3512-3520 SOL/Beamline Software Group Brazilian Synchrotron Light Laboratory (LNLS) Center of Research in Energy and Materials (CNPEM) http://lnls.cnpem.br De: [email protected] <[email protected]> em nome de Chiang, Liang-Chih [江良志] via Tech-talk <[email protected]>
Enviado: quarta-feira, 31 de julho de 2019 23:36 Para: [email protected] <[email protected]> Assunto: RE: [motorPIGCS2] can't turn on servo state of PI E-712 Hi Allan,
> I used to do the referencing through the manufacturer IDE and then ran the IOC. After performing a reference move (command FRF) and turning servo on (command SVO), I can move the axis successfully (via direct commands). However, if I run the EPICS IOC after that, the following error messages will occur repeatedly:
2019/08/01 10:21:19.114 PIGCSController::getGCSError() GCS error code = 10
> suggests (among other things) referencing the axis right in the initialization method of the PIasynAxis
I checked the files committed by you, but couldn't figure out what part is for doing reference move in PIasynAxis initialization. Would you please point it out?
Best regards.
LiangChih Chiang National Synchrotron Radiation Research Center (NSRRC)
寄件者: Allan Serra Braga Bugyi <[email protected]>
寄件日期: 2019年7月31日 下午 10:53 收件者: [email protected]; Chiang, Liang-Chih [江良志] 主旨: RE: [motorPIGCS2] can't turn on servo state of PI E-712
Hi LiangChih,
I also worked with PI controllers E-727 and C-867 using motorPIGCS2. Indeed, there is no referencing during the initialization of a PIasynAxis. I used to do the referencing through the manufacturer IDE and then ran the IOC.
I opened a pull request to the module's project, which suggests (among other things) referencing the axis right in the initialization method of the PIasynAxis. You can find the specific commit here:
https://github.com/epics-motor/motorPIGCS2/pull/1/commits/3aaf5ed20938181420edbf296a4044f57d3811b7
Best regards,
Allan S. B. Bugyi Technology Development Analyst [email protected] (+55 19) 3512-3520 SOL/Beamline Software Group Brazilian Synchrotron Light Laboratory (LNLS) Center of Research in Energy and Materials (CNPEM) http://lnls.cnpem.br De: [email protected] <[email protected]> em nome de Chiang, Liang-Chih [江良志] via Tech-talk <[email protected]>
Enviado: quarta-feira, 31 de julho de 2019 00:16 Para: [email protected] <[email protected]> Assunto: [motorPIGCS2] can't turn on servo state of PI E-712 Hello all,
I'm trying to control PI E-712 with one axis(E-711.AM5A). But the error message said that the motor driver can't turn on the servo state.
I use motor module(version 6.9) with the content of motorApp/PIGCS2Src replaced by motorPIGCS2 (https://github.com/epics-motor/motorPIGCS2).
I use MOXA NPort 5650-8-DT(serial-to-Ethernet converter) to turn the RS-232 interface of PI E-712 to Ethernet interface.
The st.cmd executes pie712.cmd, then iocInit.
pie712.cmd (stripped):
asynSetTraceMask(PIE712,-1,0x3) asynSetTraceIOMask(PIE712,-1,0x1) $(PIE712-1P)drvAsynIPPortConfigure("PIE712", "192.168.2.52:4006", 0, 0, 0) asynSetTraceMask(PIE712,-1,0x1) asynSetTraceIOMask(PIE712,-1,0x0)
$(PIE712-1P)PI_GCS2_CreateController("PIE712-1P", "PIE712", 1, 0, 0, 100, 1000)
$(PIE712-1P)dbLoadRecords("$(MOTOR)/db/PI_Support.db","P=13a:,R=PIE712-1P:,PORT=PIE712-1P,ADDR=0,TIMEOUT=1")
$(PIE712-1P)dbLoadRecords("$(ASYN)/db/asynRecord.db", "P=13a:,R=PIE712-1P:Asyn,PORT=PIE712,ADDR=0,OMAX=256,IMAX=256")
pie712_motors.substitutions:
file "$(MOTOR)/Db/asyn_motor.db" { {ALIAS, P, M, DTYP, PORT, ADDR, DESC, EGU, DIR, VELO, VBAS, ACCL, BDST, BVEL, BACC, MRES, PREC, DHLM, DLLM, INIT}
When executing pie712.cmd, there are error messages:
PI_GCS2_CreateController("PIE712-1P", "PIE712", 1, 0, 0, 100, 1000)
After iocInit, there are extra error messages:
2019/07/31 10:41:59.478 PIGCSController::getGCSError()
GCS error code = 5
Would you please provide some help? Thanks
Aviso Legal: Esta mensagem e seus anexos podem conter informações confidenciais e/ou de uso restrito. Observe atentamente seu conteúdo e considere eventual consulta ao remetente antes de copiá-la, divulgá-la ou distribuí-la. Se você recebeu esta mensagem por engano, por favor avise o remetente e apague-a imediatamente. Disclaimer: This email and its attachments may contain confidential and/or privileged information. Observe its content carefully and consider possible querying to the sender before copying, disclosing or distributing it. If you have received this email by mistake, please notify the sender and delete it immediately. |