RE: ADSpinnaker, BlackfkyS 161S7M Not enough available memory to allocate buffers for streaming

[Mark Rivers via Tech-talk <tech-talk at aps.anl.gov>]

Hi John,

 

I have verified that once I increase usbfs_memory_mb from the default of 16 up to 1000 then I can allocate a large number of buffers for USB cameras in ADSpinnaker.  I have closed the ticket with FLIR.  Sorry I forgot about that setting, even though I documented it in ADGenICam!

 

Mark

 

 

From: John Dobbins <john.dobbins at cornell.edu>
Sent: Thursday, June 6, 2024 12:53 PM
To: Mark Rivers <rivers at cars.uchicago.edu>
Subject: Re: ADSpinnaker, BlackfkyS 161S7M Not enough available memory to allocate buffers for streaming

 

Thanks Mark.   John

---

From: Mark Rivers <rivers at cars.uchicago.edu>
Sent: Thursday, June 6, 2024 1:40 PM
To: John Dobbins <john.dobbins at cornell.edu>; tech-talk at aps.anl.gov <tech-talk at aps.anl.gov>
Subject: RE: ADSpinnaker, BlackfkyS 161S7M Not enough available memory to allocate buffers for streaming

 

Hi John,

 

This problem is mentioned in the release notes for ADSpinnaker R3-5:

 

• There is a known problem on CentOS 9. The maximum number of driver buffers that Spinnaker will allow is 3. This is not a problem on Ubuntu 22 where a value over 200 is allowed on my system. Even with the limit of 3 I am able to stream the full 163 frame/s on a GS3-U3-23S6M camera. FLIR is aware of the issue.

I reported the problem to FLIR in February, with the last update and demonstration of the problem in the attached message.  I was promised that they would try to reproduce it, but I have not heard anything.  I sent them a reminder today.

 

• After configuring USB-FS memory I now have the camera running.

 

Aha!  Thanks for finding that.  Did you configure it as described here?

https://areadetector.github.io/areaDetector/ADGenICam/ADGenICam.html#linux-usb-and-gige-system-settings

 

Can you tell me the command you used so I can check and update that documentation?  I want to make sure it works on CentOS 9 as well.

 

I probably neglected to do that, which is why I thought there was a bug.

 

Thanks,

Mark

 

 

 

From: Tech-talk <tech-talk-bounces at aps.anl.gov> On Behalf Of John Dobbins via Tech-talk
Sent: Thursday, June 6, 2024 10:56 AM
To: tech-talk at aps.anl.gov
Subject: ADSpinnaker, BlackfkyS 161S7M Not enough available memory to allocate buffers for streaming

 

I have built, base-7.0.6,  areaDetectorR3-13 with ADSpinnaker master on Alma 9. I am using a FLIR BlackflyS 161S7M USB camera. This is large, 5320x3032 pixels.

 

The camera is detected but I get a "Not enough available memory to allocate buffers for streaming" error.

 

In ADSpinnakerConfig I have set numSPBuffer to minimum  = 10 (?)

 

# ADSpinnakerConfig(const char *portName, const char *cameraId, int numSPBuffers,

#                   size_t maxMemory, int priority, int stackSize)

ADSpinnakerConfig("SP1", 22671882, 10, 0, 0,0)

 

The host computer has 16G, 13.7 G free,

 

Ideas?

 

John Dobbins

 

Research Support Specialist

Cornell High Energy Synchrotron Source

Cornell University

 

www.chess.cornell.edu

 

 

 

 

 

[root@lnx615 iocSpinnaker]# ../../bin/linux-x86_64/spinnakerApp st.cmd.BlackflyS_161S7M

< envPaths

epicsEnvSet("IOC","iocSpinnaker")

epicsEnvSet("TOP","/nfs/chess/epics/det/support_flir/areaDetector-R3-13/ADSpinnaker/iocs/spinnakerIOC")

epicsEnvSet("ADSPINNAKER","/nfs/chess/epics/det/support_flir/areaDetector-R3-13/ADSpinnaker/iocs/spinnakerIOC/../..")

epicsEnvSet("SUPPORT","/nfs/chess/epics/det/support_flir")

epicsEnvSet("ASYN","/nfs/chess/epics/det/support_flir/asyn-R4-45")

epicsEnvSet("AREA_DETECTOR","/nfs/chess/epics/det/support_flir/areaDetector-R3-13")

epicsEnvSet("ADSUPPORT","/nfs/chess/epics/det/support_flir/areaDetector-R3-13/ADSupport")

epicsEnvSet("ADCORE","/nfs/chess/epics/det/support_flir/areaDetector-R3-13/ADCore")

epicsEnvSet("AUTOSAVE","/nfs/chess/epics/det/support_flir/autosave-R5-11")

epicsEnvSet("BUSY","/nfs/chess/epics/det/support_flir/busy-R1-7-4")

epicsEnvSet("CALC","/nfs/chess/epics/det/support_flir/calc-R3-7-5")

epicsEnvSet("SNCSEQ","/nfs/chess/epics/det/support_flir/seq-R2-2-9")

epicsEnvSet("SSCAN","/nfs/chess/epics/det/support_flir/sscan-R2-11-5")

epicsEnvSet("DEVIOCSTATS","/nfs/chess/epics/det/support_flir/iocStats-3-1-16")

epicsEnvSet("EPICS_BASE","/nfs/chess/epics/det/base-7.0.6")

epicsEnvSet("ADGENICAM","/nfs/chess/epics/det/support_flir/areaDetector-R3-13/ADGenICam")

errlogInit(20000)

dbLoadDatabase("/nfs/chess/epics/det/support_flir/areaDetector-R3-13/ADSpinnaker/iocs/spinnakerIOC/dbd/spinnakerApp.dbd")

spinnakerApp_registerRecordDeviceDriver(pdbbase)

# Use this line for a specific camera by serial number, in this case a BlackFlyS GigE

epicsEnvSet("CAMERA_ID", "22671882")

epicsEnvSet("GENICAM_DB_FILE", "/nfs/chess/epics/det/support_flir/areaDetector-R3-13/ADGenICam/db/FLIR_BFS_U3_161S7M.template")

< st.cmd.base

# Prefix for all records

epicsEnvSet("PREFIX", "13SP1:")

# The port name for the detector

epicsEnvSet("PORT",   "SP1")

# Really large queue so we can stream to disk at full camera speed

epicsEnvSet("QSIZE",  "2000")  

# The maximim image width; used for row profiles in the NDPluginStats plugin

epicsEnvSet("XSIZE",  "2048")

# The maximim image height; used for column profiles in the NDPluginStats plugin

epicsEnvSet("YSIZE",  "2048")

# The maximum number of time series points in the NDPluginStats plugin

epicsEnvSet("NCHANS", "2048")

# The maximum number of frames buffered in the NDPluginCircularBuff plugin

epicsEnvSet("CBUFFS", "500")

# The search path for database files

# This is for Windows

epicsEnvSet("EPICS_DB_INCLUDE_PATH", "/nfs/chess/epics/det/support_flir/areaDetector-R3-13/ADCore/db;/nfs/chess/epics/det/support_flir/areaDetector-R3-13/ADGenICam/db;/nfs/chess/epics/det/support_flir/areaDetector-R3-13/ADSpinnaker/iocs/spinnakerIOC/../../db")

# This is for Linux

#epicsEnvSet("EPICS_DB_INCLUDE_PATH", "$(ADCORE)/db:$(ADGENICAM)/db:$(ADSPINNAKER)/db")

# Define NELEMENTS to be enough for a 5320x3032 (color) image

epicsEnvSet("NELEMENTS", "16130240")

# ADSpinnakerConfig(const char *portName, const char *cameraId, int numSPBuffers,

#                   size_t maxMemory, int priority, int stackSize)

ADSpinnakerConfig("SP1", 22671882, 10, 0, 0,0)

2024/06/06 11:46:16.990 ADSpinnaker::connectCamera exception Spinnaker: Not enough available memory to allocate buffers for streaming. [-1016]

2024/06/06 11:46:16.990 ADSpinnaker:ADSpinnaker:  camera connection failed (3)

 

Number of cameras detected: 1

Camera 0

Device Vendor Name   (DeviceVendorName):FLIR

Device Model Name (DeviceModelName):Blackfly S BFS-U3-161S7M

Device Serial Number (DeviceSerialNumber):22671882

Device Version (DeviceVersion):2210.0.657.0

Device Type (DeviceType):USB3Vision