"assert (semTake(client_lock, WAIT_FOREVER)==OK)"
A semTake within an assert often causes this problem.
change the statement to:
status = semTake( ... )
assert( status == OK )
and all will be well.
AH
> Date: Wed, 29 Jan 2003 10:11:02 -0800
> From: "Leonard J. Reder" <[email protected]>
> X-Accept-Language: en
> MIME-Version: 1.0
> To: "EPICS Tech Talk (E-mail)" <[email protected]>
> Subject: [Fwd: align CPU Error message????]
> Content-Transfer-Encoding: 7bit
> List-Help: <http://www.aps.anl.gov/epics/mail.php>
>
> Hello,
>
> Not sure what to make of this error message but since the message
> below says to email tech-talk I thought I would see if others
> have information for me on this. See below.
>
> Len
>
> -------- Original Message --------
> Subject: align CPU Error message????
> Date: Wed, 29 Jan 2003 10:08:50 -0800
> From: "Leonard J. Reder" <[email protected]>
>
> Hello Kevin,
>
> Mark and Andrew asked me to add some instances of btSeq for k1.m11 and
> k2.m11 on the ldls. I attempted this and noticed the error given below.
> I put the old start up script back in place and got this error. It was
> booting up fine before or maybe I just did not notice this error message
> once in awhile. At any rate all the main sequencer tasks are running
> but
> for each sequencer there is no fault or commanding task running.
>
> I am not sure what is going on here so for now I will just finish adding
> the new keywords. Here is the error message:
>
> k1m6pAlign: A call to "assert (semTake(client_lock, WAIT_FOREVER)==OK)"
> failed in ../iocinf.c at 1046
> Please send a copy of the output from "tt (0xfde078)" and a copy of this
> message
> to the author or "[email protected]"
> This problem occurred in "@(#)Version R3.13.0.beta.12 $$Date: 1998/08/18
> 02:02:32 $$"
> k1m7pAlign: A call to "assert (semTake(client_lock, WAIT_FOREVER)==OK)"
> failed in ../access.c at 1074
> Please send a copy of the output from "tt (0xfbb510)" and a copy of this
> message
> amoeba Flux, Pixels, Radius, Xcen, Ycen = 26.053 27106 998.846 428.953
> -1112.784
> errlog = 14 messages were discarded
> filename="../taskwd.c" line number=175
> task 10a2c68 seqAux suspended
>
> Here is the output from tt,
>
> al>tt 0xfde078
> 176cb4 vxTaskEntry +60 : sequencer (1096f10, 2710, 1094cd8)
> 17d1b44 sequencer +a4 : seq_connect (1096f10)
> 17cf9e8 seq_connect +17c: seq_pvMonitor (1096998, 28)
> 17d4544 seq_pvMonitor +164: ca_flush_io ()
> 174be38 ca_flush_io +98 : cac_mux_io (fddf38)
> 1743aa4 cac_mux_io +24 : cac_clean_iiu_list ()
> 17408cc cac_clean_iiu_list+74 : epicsAssert (176eb64, 416, 176eb70, 0)
> 1737a14 epicsAssert +14c: taskSuspend ()
> value = 0 = 0x0
>
> Also I think I will send this out to tech-talk and see if any
> interesting replies come back.
>
> Thanks,
> Len
> --
> ____________________________________________________
> Leonard J. Reder
> Jet Propulsion Laboratory
> Interferometry Systems and Technology Section 383
> Email: [email protected]
> Phone (Voice): 818-354-3639
> Phone (FAX): 818-354-4357
> Mail Address:
> Mail Stop: 171-113
> 4800 Oak Grove Dr.
> Pasadena, CA. 91109
> ---------------------------------------------------
- Replies:
- RE: [Fwd: align CPU Error message????] Jeff Hill
- Navigate by Date:
- Prev:
[Fwd: align CPU Error message????] Leonard J. Reder
- Next:
Re: Can't build the CMLOG under Tornado 2.0 for mv162, ppc etc. Ron MacKenzie
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
<2003>
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
- Navigate by Thread:
- Prev:
RE: [Fwd: align CPU Error message????] Jeff Hill
- Next:
RE: [Fwd: align CPU Error message????] Jeff Hill
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
<2003>
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
|