Have you checked out the M540 Stepper motor controller from Highland
technologies. That is what we use at JLAB. With Vxworks and EPICS.
Hope this helps
Brad Cumbia
Accelerator Network Administrator/Senior Controls Technologist
Thomas Jefferson National Accelerator Facility
Electrical Engineering Support Group
Instrumentation & Control Systems
Accelerator Computing Environment
12000 Jefferson Avenue
Newport News, Virginia 23606
Phone (757)269-5839
Pager (757)584-5839
Fax (757)269-7309
____ __ ___
/ / // \/ _ \
__/ / // - / _ /
/___/___/._/_.__/
=================================================
()
------------------------------------------------
||* * * * * * * * * * OOOOOOOOOOOOOOOOOOOOOOOOO|
||* * * * * * * * * * :::::::::::::::::::::::::|
||* * * * * * * * * * OOOOOOOOOOOOOOOOOOOOOOOOO|
||* * * * * * * * * * :::::::::::::::::::::::::|
||* * * * * * * * * * OOOOOOOOOOOOOOOOOOOOOOOOO|
||:::::::::::::::::::::::::::::::::::::::::::::|
||OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO|
||:::::::::::::::::::::::::::::::::::::::::::::|
||OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO|
||:::::::::::::::::::::::::::::::::::::::::::::|
||OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO|
||:::::::::::::::::::::::::::::::::::::::::::::|
||OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO|
||----------------------------------------------
||
||
||
||
Darrell Nineham wrote:
Yes there is, Hytec produce 2404
It is in use at Brookhaven. They have been using them for a few years; I
don't know if they have EPICS support (anyone out there in tech-talk
land know the answer ?). The E500 has not been produced for some years
and our 2404 was adopted at BNL to replace exactly that unit.
Darrell Nineham
Hytec Electronics Ltd.
Tel: +44 (0) 118 975 7770
Fax: +44 (0) 118 975 7566
Web: www.hytec-electronics.co.uk
++++++++++++++++++++++++++++++++++++++++++++
This email and any files transmitted with it are confidential and
intended solely for the use of the individual or entity to whom they are
addressed. If you have received this email in error, please notify the
sender immediately. The views expressed in the message are those of the
individual author and may not necessarily represent the views of Hytec
Electronics Ltd.
-----Original Message-----
From: Peregrine M. McGehee [mailto:[email protected]]
Sent: 21 November 2005 16:18
To: [email protected]
Subject: CAMAC-based stepper motor controllers
I am looking for multi-channel CAMAC-based stepper motor controllers
that have EPICS device support available and are still being
manufactured. Anything out there besides the DSP E500?
Best regards,
Peregrine
- References:
- RE: CAMAC-based stepper motor controllers Darrell Nineham
- Navigate by Date:
- Prev:
EPICS base compiling using Visual C++ 2005 Express guobao shen
- Next:
Re: EPICS base compiling using Visual C++ 2005 Express Vladimir Sirotenko
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
<2005>
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
- Navigate by Thread:
- Prev:
RE: CAMAC-based stepper motor controllers Darrell Nineham
- Next:
RE: CAMAC-based stepper motor controllers Lawrence T. Hoff
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
<2005>
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
|