Experimental Physics and
Industrial Control System

"Kasemir, Kay" <[email protected]> · Thu, 5 Jun 2014 15:08:20 +0000

Hi:

Based on separate emails, the issue was about sometimes using 

EPICS_BASE=/opt/epics/base

and in other places

EPICS_BASE=/opt/epics/base-3.15.0.1

Once it was set consistently and correctly, all's fine.

-Kay

On Jun 5, 2014, at 9:57 AM, Ralph Lange <[email protected]>
 wrote:

> On 05/06/2014 12:26, Benjamin Franksen wrote:
>> Hm, I had once successfully compiled it with 3.15. Let's see... yes
>> 2.1.12 states that in the release notes.
>> 
>> So, shareLib.h went away 3.15? That's new to me. Is there a replacement?
>> How to upgrade while still maintaining 3.14 compatibility?
> 
> shareLib.h is still there.
> My guess: Vikram unpacked EPICS Base, but didn't build it.
> 
> ~Ralph
> 
> 
>> On Wednesday, June 04, 2014 20:09:06 Mark Rivers wrote:
>>> You are using EPICS 3.15.  Do you have a reason for using that?  It is
>>> still not ready for production systems.  Should you be using
>>> 3.14.12.4 instead?
>>> 
>>> Mark
>>> 
>>> ________________________________
>>> From: [email protected] [[email protected]] on
>>> behalf of Vikram Bhagat [[email protected]] Sent: Wednesday,
>>> June 04, 2014 3:02 PM
>>> To: epics talk
>>> Subject: sequencer installation
>>> 
>>> Hello,
>>>     I am trying to install sequencer but could not build
>>> Below is the log an anyone guide me what is wrong with installation.
>>> 
>>> 
>>> [root@sarva-PC sncseq]# make
>>> make -C ./configure install
>>> make[1]: Entering directory `/opt/epics/modules/sncseq/configure'
>>> make -C O.linux-x86_64 -f ../Makefile TOP=../.. T_A=linux-x86_64
>>> install make[2]: Entering directory
>>> `/opt/epics/modules/sncseq/configure/O.linux-x86_64' perl -CSD
>>> /opt/epics/base/bin/linux-x86_64/convertRelease.pl checkRelease
>>> make[2]: Leaving directory
>>> `/opt/epics/modules/sncseq/configure/O.linux-x86_64' make[1]: Leaving
>>> directory `/opt/epics/modules/sncseq/configure' make -C ./src install
>>> make[1]: Entering directory `/opt/epics/modules/sncseq/src'
>>> make -C ./pv install
>>> make[2]: Entering directory `/opt/epics/modules/sncseq/src/pv'
>>> make -C O.linux-x86_64 -f ../Makefile TOP=../../.. T_A=linux-x86_64
>>> install make[3]: Entering directory
>>> `/opt/epics/modules/sncseq/src/pv/O.linux-x86_64' make[3]: *** No
>>> rule to make target `/opt/epics/base-3.15.0.1/include/shareLib.h',
>>> needed by `pvNew.o'.  Stop. make[3]: Leaving directory
>>> `/opt/epics/modules/sncseq/src/pv/O.linux-x86_64' make[2]: ***
>>> [install.linux-x86_64] Error 2
>>> make[2]: Leaving directory `/opt/epics/modules/sncseq/src/pv'
>>> make[1]: *** [pv.install] Error 2
>>> make[1]: Leaving directory `/opt/epics/modules/sncseq/src'
>>> make: *** [src.install] Error 2
>>> [root@sarva-PC sncseq]#
>>> 
>>> 
>>> 
>>> I set
>>> EPICS_BASE=/opt/epics/base
>>> in configure/RELEASE
>>> 
>>> 
>>> Thanks
>>> Vikram
> 

Experimental Physics and Industrial Control System

Experimental Physics and
Industrial Control System