Experimental Physics and Industrial Control System
Hi Kevin and all.
Is it possible to implement this closed loop in such a way that, whenever the motor is taken out of its initial position, EPICS commands it to move back to the original position? This is not happening in the current setup.
Also, when I try to move, the RCNT increases up to ~50, and it takes a long time for the motor to reach the position RDBD deadband. Does arithmetic mode help here?
Thanks again.
Guilherme Jovanini Montagner
+55 19 99806.9117
+55 19 2517.8911
guilherme at setup.com.br
Labview Certified Developer
----- Mensagem original -----
De: "guilherme" <guilherme at setup.com.br>
Para: "Kevin M. Peterson" <kmpeters at anl.gov>
Cc: "tech-talk" <tech-talk at aps.anl.gov>
Enviadas: Quarta-feira, 30 de setembro de 2020 13:13:54
Assunto: Re: Implementing closed loop on EPICS level
Hello Kevin!
Thanks a lot!! It worked!
Now I only have a problem that is the virtual encoder channel that I have setup on m11. Apparently EPICS is trying to control this motor, because I got following errors on the PMAC controller on axis 11, and also a DACLimit warning.
Is it possible to disable m11 actuation?
Also, is there a lower limit to my RDBD value? I wanted to get it as low as 600nm
Thanks!
Guilherme Jovanini Montagner
+55 19 99806.9117
+55 19 2517.8911
guilherme at setup.com.br
Labview Certified Developer
----- Mensagem original -----
De: "Kevin M. Peterson" <kmpeters at anl.gov>
Para: "guilherme" <guilherme at setup.com.br>
Cc: "tech-talk" <tech-talk at aps.anl.gov>
Enviadas: Terça-feira, 29 de setembro de 2020 11:36:19
Assunto: Re: Implementing closed loop on EPICS level
You might be able to make it work by doing the following:
1. Set m1's RDBL field to m11.REP
2. Set m1's RRES field to whatever is required to convert between
m11.REP and m1's EGU.
3. Set m1's URIP = Yes and UEIP = No
Kevin
On 9/29/20 8:55 AM, Guilherme Jovanini Montagner wrote:
> Hi Kevin
> Thank you for your response.
> I tried with UEIP = 1, but then it seems to use the motor 1 encoder (which is just the phase value, or open loop value), and not the m11 encoder that I have setup.
> Then it disregards the m11 encoder reading
>
> Guilherme Jovanini Montagner
> +55 19 99806.9117
> +55 19 2517.8911
> guilherme at setup.com.br
>
> Labview Certified Developer
>
- Replies:
- Re: Implementing closed loop on EPICS level Peterson, Kevin M. via Tech-talk
- References:
- Implementing closed loop on EPICS level Guilherme Jovanini Montagner via Tech-talk
- Re: Implementing closed loop on EPICS level Peterson, Kevin M. via Tech-talk
- Re: Implementing closed loop on EPICS level Guilherme Jovanini Montagner via Tech-talk
- Re: Implementing closed loop on EPICS level Peterson, Kevin M. via Tech-talk
- Re: Implementing closed loop on EPICS level Guilherme Jovanini Montagner via Tech-talk
- Navigate by Date:
- Prev:
Re: Implementing closed loop on EPICS level Guilherme Jovanini Montagner via Tech-talk
- Next:
Re: Multiple Archiver Appliances on same host, different NICs Phillip A. Sorensen via Tech-talk
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
<2020>
2021
2022
2023
2024
- Navigate by Thread:
- Prev:
Re: Implementing closed loop on EPICS level Guilherme Jovanini Montagner via Tech-talk
- Next:
Re: Implementing closed loop on EPICS level Peterson, Kevin M. via Tech-talk
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
<2020>
2021
2022
2023
2024