Hi Mark,
As Torsten and Jeong Han have already said, the Diamond Ethercat EPICS support is available [1], but it does not support motion.
For some digital I/O and analog I/O we would use kit from our supported set [2].
The master in our setup runs on a Dell R310, using Redhat MRG (real time pre-empt rt kernel).
The minimal ethercat kit would be: EK1100 coupler, EL1014 (digital input), EL3104 (analogue input), EL2024 (digital output), EL4134 (analogue output).
Best regards,
Ronaldo
[1] https://github.com/dls-controls/ethercat
[2] See https://epics.anl.gov/tech-talk/2015/msg01665.php
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Torsten Bögershausen
Sent: 07 February 2018 05:29
To: Mark Rivers; [email protected]
Subject: Re: EtherCAT newbie question
Hej Mark,
this is what we use for our motion control test/development crates:
# CPU: CX5130
# Configure EL1018 digital input terminal
# Configure EL2808 digital output terminal
# Configure EL5101 incremental encoder terminal, motor 1
# Configure EL5101 incremental encoder terminal, motor 2
# Configure EL9505 Power supply terminal 5V
# Configure EL1252 digital input terminal
# Configure EL7037 stepper drive terminal, motor 1
# Configure EL7037 stepper drive terminal, motor 2
(No analog IO in our motion crates ;-)
No sure if you have access to this page about other terminals for motion:
https://confluence.esss.lu.se/display/MCAG/Motion+Controller
HTH
/Torsten
PS:
As Han Lee pointed out, there are different SW packages:
- Beckhoff TwinCAT
- Linux ("scanner" from DLS and ecat2 from PSI) (but no motion control)
- Linux ECMC from ESS http://icalepcs2017.vrws.de/talks/mocpl05_talk.pdf
And we are happy to help.
On 06/02/18 20:37, Mark Rivers wrote:
> I am interested in trying out EtherCAT with a simple inexpensive setup. What
> are the minimum parts I need to buy if I want to use the EPICS EtherCAT driver
> to control some digital I/O, analog I/O, and a stepper motor? I looked at the
> Beckhoff website, but I find it overwhelming.
>
> Thanks,
>
> Mark
>
--
This e-mail and any attachments may contain confidential, copyright and or privileged material, and are for the use of the intended addressee only. If you are not the intended addressee or an authorised recipient of the addressee please notify us of receipt by returning the e-mail and do not use, copy, retain, distribute or disclose the information in or attached to the e-mail.
Any opinions expressed within this e-mail are those of the individual and not necessarily of Diamond Light Source Ltd.
Diamond Light Source Ltd. cannot guarantee that this e-mail or any attachments are free from viruses and we cannot accept liability for any damage which you may sustain as a result of software viruses which may be transmitted in or with the message.
Diamond Light Source Limited (company no. 4375679). Registered in England and Wales with its registered office at Diamond House, Harwell Science and Innovation Campus, Didcot, Oxfordshire, OX11 0DE, United Kingdom
- Replies:
- Re: EtherCAT newbie question Stubbs, Scott A.
- RE: EtherCAT newbie question Linda.Pratt
- References:
- EtherCAT newbie question Mark Rivers
- Re: EtherCAT newbie question Torsten Bögershausen
- Navigate by Date:
- Prev:
Re: procServ under systemd service Hinko Kocevar
- Next:
Re: procServ under systemd service Ralph Lange
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
<2018>
2019
2020
2021
2022
2023
2024
- Navigate by Thread:
- Prev:
Re: EtherCAT newbie question Torsten Bögershausen
- Next:
Re: EtherCAT newbie question Stubbs, Scott A.
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
<2018>
2019
2020
2021
2022
2023
2024
|